📐 Your Driveway
ft
ft
Our concrete driveway presets use 10 ft for one car and 20 ft for two side by side.
in
3 in over a stone base is a common residential build; 4 to 6 in if there is no base (full depth); 1.5 to 2 in for an overlay.
in
6 to 8 in under 3 in of asphalt. Enter 0 for full-depth asphalt or an overlay.
lb/sq yd/in
The weight of 1 sq yd of pavement 1 in thick. 110 is the figure Texas DOT uses; ask your plant for theirs.
%
Our planning figure for edges, uneven subgrade and the last partial load. Not an industry standard.
✓ Results
11.55 tons
Hot-Mix Asphalt to Order
Driveway Area 600 sq ft (66.7 sq yd)
Asphalt Volume (compacted) 5.56 cu yd
Suggested Lifts 2 lifts of about 1.5 in
Aggregate Base Stone 18.67 tons
Base Stone Volume (loose) 13.33 cu yd

Pricing concrete for the same driveway?

Use the concrete driveway calculator →

On this page

  1. How to Calculate Asphalt Tonnage
  2. Driveway Thickness and Base
  3. Asphalt Tons by Driveway Size
  4. Checking a Paving Quote
  5. Frequently Asked Questions

How to Calculate Asphalt Tonnage

Tons = (Square feet ÷ 9) × Thickness (in) × 110 ÷ 2,000
  1. Measure the area. Length × width in feet. For a curved or flared drive, split it into rectangles and add them, or use the square footage calculator.
  2. Convert to square yards. Divide by 9. Highway specifications work in square yards, and many paving quotes do too.
  3. Multiply by thickness and by the rate. 110 lb per square yard per inch is the figure Texas DOT’s specification uses to convert tons to compacted thickness.
  4. Divide by 2,000 for tons, then add a small allowance for edges and an uneven subgrade.

Worked example: 12 × 50 ft = 600 sq ft = 66.7 sq yd. At 3 in: 66.7 × 3 × 110 = 22,000 lb = 11.0 tons. With the 5% allowance, about 11.6 tons.

The thickness in the formula is compacted thickness. Loose mix out of the truck is thicker than the finished mat and gets rolled down, but the weight does not change, so tons calculated from the compacted figure are what the plant loads.

Driveway Thickness and Base

The Illinois Asphalt Pavement Association describes these builds for residential driveways:

BuildAsphaltAggregate BaseNotes
Asphalt over aggregate base3 in6 to 8 in compactedThe common residential build
Full-depth asphalt4 in may be adequate; 5 to 6 in strongerNonePlaced on firm, dry subgrade
Overlay on a sound old drive1.5 to 2 inExisting pavementRepair failed areas first

Their rule of thumb is that 1 in of asphalt does the work of about 3 in of aggregate base, which is why a full-depth drive can skip the stone. Either way, the ground underneath has to be firm and dry before paving, and the surface needs enough slope to shed water.

If you are preparing the base yourself, the stone figures here match the gravel calculator: crushed stone at 1.4 tons per cubic yard, with 20% extra because you measure the compacted depth but buy loose stone. Dig-out volume is a separate question; the excavation calculator covers that, including swell.

Asphalt Tons by Driveway Size

Compacted hot mix at 110 lb per square yard per inch, before any allowance:

Driveway2 in3 in4 in
10 × 20 ft (200 sq ft)2.443.674.89
20 × 20 ft (400 sq ft)4.897.339.78
12 × 50 ft (600 sq ft)7.3311.0014.67
24 × 40 ft (960 sq ft)11.7317.6023.47
10 × 100 ft (1,000 sq ft)12.2218.3324.44

The short version: every 100 sq ft of driveway takes about 0.61 tons per inch of thickness. Going from 2 in to 3 in on a 12 × 50 ft drive adds about 3.7 tons.

Checking a Paving Quote

Frequently Asked Questions

How do I calculate how many tons of asphalt I need?

Work out the area in square yards (square feet ÷ 9), multiply by the compacted thickness in inches, then by 110 lb, the weight of one square yard of pavement one inch thick. Divide by 2,000 for tons. A 12 × 50 ft driveway is 66.7 sq yd; at 3 in that is 66.7 × 3 × 110 = 22,000 lb, or 11.0 tons before any allowance.

How much does a ton of asphalt cover?

At the 110 lb rate, one ton covers about 18.2 sq yd (164 sq ft) at 1 in. So at 2 in it covers about 82 sq ft, at 3 in about 55 sq ft, and at 4 in about 41 sq ft. Your plant’s mix may weigh a little more or less, which is why the rate is adjustable above.

How thick should an asphalt driveway be?

The Illinois Asphalt Pavement Association gives two common builds: 3 in of asphalt over 6 to 8 in of compacted aggregate, or full-depth asphalt placed straight on firm subgrade, where 4 in may be adequate but 5 to 6 in is stronger. Heavy vehicles or soft soil push toward the thicker end.

What does 110 lb per square yard per inch mean?

It is the weight of a piece of compacted pavement one square yard in area and one inch thick. State highway departments use it to convert between tons delivered and thickness placed; Texas DOT, for example, bases thickness on 110 lb/sq yd per inch unless the plans say otherwise. It works out to about 147 lb per cubic foot. Other agencies and plants use slightly different figures for their own mixes, so ask the plant supplying yours.

Is asphalt put down in one layer?

Often not. The IAPA says asphalt is best placed in lifts: 2 to 3 in may be spread as two layers of about 1.5 in each, and a 4 in mat placed as 2.5 in, compacted, then the remaining 1.5 in on top. The calculator splits anything over 2.5 in into equal lifts; that cut-off is our reading of those examples, not a published rule.

How much gravel base do I need under an asphalt driveway?

Six to 8 in of compacted crushed stone under 3 in of asphalt is the common build. Order more than the compacted volume: our figure adds 20% for plate compaction, then converts at 1.4 tons per cubic yard, the same numbers the gravel calculator uses. A 600 sq ft drive at 6 in needs about 18.7 tons of base.

Can I use less base if I use more asphalt?

Yes, within reason. The IAPA equivalency is that 1 in of asphalt is worth about 3 in of aggregate base. That is why full-depth asphalt driveways can skip the stone base entirely at 4 to 6 in thick. The subgrade still has to be firm and dry before paving.

How thick should an asphalt overlay be?

For a driveway, a surface course of 1.5 to 2 in usually suffices, according to the IAPA. An overlay only works over a sound base: if the existing drive has deep ruts or broken, alligator-cracked areas, those need repair or removal first. Set the base thickness to 0 for an overlay.

Can I pave an asphalt driveway myself?

Hot-mix asphalt has to be placed and rolled while it is hot, which takes a paver or skilled hand crew and a roller, so driveways are nearly always contractor jobs. This calculator is for checking the tonnage on a quote, sizing the stone base you might prepare yourself, and comparing options. For a driveway you can build yourself, see the gravel driveway calculator.

Asphalt or concrete for a driveway?

Both work; the choice is mostly about up-front cost, climate and maintenance. If you are comparing, the concrete driveway calculator gives yardage and thickness for the same footprint, so you can put the two material lists side by side.

Sources & Standards

Estimates for planning only. This calculator sizes material quantities. It does not size structural members, verify load paths, or confirm compliance with the code in your jurisdiction. Local requirements — frost depth, footing sizes, permits, and inspections — override anything here. Check with your local code enforcement office or building department before you build. They are the authority that inspects and signs off the work, they amend the model codes, and what they say overrides any figure on this page. For structural or safety-critical work, have the design checked by a licensed engineer or contractor as well. See our full method and assumptions.

Last updated · How we calculate