Ice dams start in the attic. Check your insulation.
Use the attic insulation calculator →On this page
How to Calculate Heat Cable Length
This is the method in King Electric’s design guide for its self-regulating roof and gutter cable:
- Roof edge zigzag: the length of eave × a multiplier from the table below, set by the overhang and the roof type.
- Roof extension: half the roof edge again. This is the drip loop that hangs from the roof edge into the gutter, or forms a drip edge where there is no gutter.
- Gutters: 1 ft of cable per foot of gutter, two runs if the gutter is 6 in wide or more. The guide states the 1 ft rule for standard non-metal roofs; on a metal roof, check your cable’s instructions.
- Downspouts: the total downspout length plus 1 ft. A downspout in the middle of a run is looped down and back up, so double it.
- Valleys: the guide says to run cable two thirds of the way up and down each valley. We read that as up and back, so 4/3 × the valley length.
- Connections: 1 ft per power connection, 2 ft per splice, 3 ft per tee.
Worked example: a 48 ft eave on a shingle roof with a 12 in overhang, 48 ft of gutter, one 22 ft downspout at the end, 2 power connections and 3 splices. That is 48 × 2.8 = 134.4, plus 24, plus 48, plus 23, plus 2 + 6 = 237.4 ft. (The guide prints 238.4 ft for this example, but it counts 3 ft for the two 1 ft power connections; its own parts add to 237.4.)
Cable Multiplier and Loop Height
Cable per foot of roof edge, with the height the loops reach up the roof, from King Electric’s tables. Loops are 24 in wide on standard roofs and on 24 in seam metal, and 18 in wide on 18 in seam metal.
| Eave Overhang | Shingle / Shake | Metal, 18 in Seam | Metal, 24 in Seam |
|---|---|---|---|
| None | 2.0 × (18 in high) | 2.5 × (18 in high) | 2.0 × (18 in high) |
| 12 in | 2.8 × (18 in high) | 2.8 × (24 in high) | 2.4 × (24 in high) |
| 24 in | 3.8 × (30 in high) | 3.6 × (36 in high) | 2.9 × (36 in high) |
| 36 in | 4.8 × (42 in high) | 4.3 × (48 in high) | 3.6 × (48 in high) |
The point of the loop height is to carry the cable above the line of the outside wall, where the roof starts to sit over heated space. That is why a deeper overhang takes more cable. These are one manufacturer’s figures for its cable; if yours gives different ones, use the override box.
What Heat Cable Can and Cannot Do
- It removes ice, not snow. King’s guide says the cable is designed to remove ice, not accumulated snow.
- It will not hold snow on the roof. The guide says it will not keep snow or ice from falling off, and points to snow fences or snow guards for that.
- It keeps a drainage path open. The loops, the gutter run and the downspout run together give melt water a way off the roof.
- It does not fix the cause. Ice dams start in the attic; see below.
Fix the Cause: The Attic
The Department of Energy’s Building America Solution Center says ice dams need three things: snow on the roof, a poorly air-sealed and/or poorly insulated attic, and freezing temperatures. Heated air escaping into the attic warms the underside of the roof deck and melts the snow; the water runs down to the cold eaves and refreezes.
Its three fixes are to fully air seal the ceiling, thoroughly insulate the attic, and ventilate the roof, and it calls sealing the air leaks into the attic the most important step. Heat cable is a reasonable stopgap on a roof that keeps damming, but the lasting fix is in the attic. The ice dam guide walks through the attic fix step by step and what to do about a dam that is leaking now. The attic insulation calculator and R-value guide cover the insulation side.
Installation Rules from the Guide
- Ground-fault protection: connect only to ground-fault protected breakers or outlets, installed to national and local codes and protected from rain and melt water.
- Circuit rating: do not exceed the amp rating of the overcurrent device. Check your cable’s maximum circuit length for your breaker size.
- On the surface only: never under the roof covering, behind walls, or through walls, ceilings or floors.
- Clean gutters first: gutters and downspouts must be free of leaves and debris.
- Downspouts: if a downspout ties into a drain, the cable should extend below the frost line, and end seals should not sit at the lowest point of a downspout or anywhere wet.
Electrical work is governed by code where you live. If you are adding a circuit or an outdoor outlet, use a licensed electrician.
Frequently Asked Questions
How much heat cable do I need for my roof?
About 2.5 to 5.3 times the length of the roof edge for the zigzag and drip loop, plus the gutters and downspouts. King Electric’s design guide multiplies the roof edge by 2.0 to 4.8 depending on the overhang and roof type, adds half the roof edge again for the drip loop, then adds the gutter length, the downspout length plus 1 ft, and small allowances for connections. A 48 ft eave with a 12 in overhang, 48 ft of gutter and a 22 ft downspout comes to about 237 ft.
Why does a bigger overhang need more cable?
King’s guide says to extend the top of each loop beyond where the wall joins the roof, and a deeper overhang puts that line further up the roof. King’s tables raise the loop height from 18 in with no overhang to 42 in with a 36 in overhang on a standard roof, and the cable per foot of edge from 2.0 to 4.8.
Do I need heat cable in the gutters and downspouts?
Yes, if you have them. Melted water has to drain away or it refreezes in the gutter. The guide adds 1 ft of cable per foot of gutter (two runs in gutters 6 in wide or more) and 1 ft per foot of downspout. A downspout in the middle of a run is looped down and back up, so it takes double.
Will heat cable stop ice dams?
It keeps a channel open so melt water can drain, but it treats the symptom. King’s guide says its cable is designed to remove ice, not accumulated snow, and will not keep snow or ice from falling off the roof. The Department of Energy’s Building America Solution Center says ice dams need snow on the roof, a poorly air-sealed or poorly insulated attic, and freezing temperatures, and that the most important fix is sealing air leaks into the attic.
What causes ice dams?
According to the Department of Energy’s Building America Solution Center, heated air from the house escapes into the attic and warms the underside of the roof deck, melting the snow above. The melt water runs down the roof until it reaches the cold eaves, where it refreezes. Its three recommended fixes are to air seal the ceiling, insulate the attic, and ventilate the roof. Our attic insulation calculator sizes the insulation, and the ice dam guide covers the full fix.
Does heat cable need a GFCI?
King’s guide says to connect only to ground-fault protected circuit breakers or outlets, installed to national and local codes and protected from rain and melt water, and not to exceed the amp rating of the overcurrent device. Check your cable’s maximum circuit length for your breaker, and use an electrician if you are adding a circuit.
Can heat cable go under the shingles?
No. The guide says not to install the cable underneath any roof covering, not to hide it behind walls, and not to run it through walls, ceilings or floors. It has to stay accessible on the surface.
How much extra cable do connections take?
King adds 1 ft for each power connection, 2 ft for each splice and 3 ft for each tee, and says splices and tees should be avoided where possible. Planning one continuous run saves the extra cable.
Do other brands use the same numbers?
Not necessarily. The multipliers here are King Electric’s for its self-regulating cable, and other makers publish their own layouts and kit lengths. If your cable’s instructions give a different figure per foot of roof edge, enter it in the override box.
Sources & Standards
- King Electric: SR Heating Cable Design for Roof and Gutter Applications — Cable length formula, roof edge multipliers and loop heights by overhang, installation rules
- US DOE Building America Solution Center: Attic Air Sealing, Insulating, and Ventilating for Ice Dam Prevention — What causes ice dams and the three recommended fixes
Estimates for planning only. The figures here follow published model codes and industry standards, but those are adopted and amended locally, and older buildings are often legally exempt from the current edition. Check with your local code enforcement office or building department before you order or build — they are the authority that inspects the work, and what they require overrides anything on this page. See our full method and assumptions.