📐 Room and Trim
ft
For an L-shaped room, add the runs up and use the total linear feet box instead.
ft
The perimeter is what trim follows, so both dimensions matter.
ft
Already measured, or an odd-shaped room? Put the total here and it overrides the two boxes above.
pcs
Baseboard stops at a door. Crown does not — set this to 0 for crown.
ft
A standard interior door is about 3 ft including the jamb.
Longer stock means fewer joints on a long wall, but it is harder to get home.
Crown is cut on a compound angle and wastes more; coping a corner eats an end.
✓ Results
Perimeter 52 linear ft
Less Door Openings −6 linear ft
Net Trim Needed 46 linear ft
5 pieces
Stock Lengths to Buy
Total Purchased 60 linear ft
Inside Corners (to cope or miter) 4

Working out the floor that goes under it?

Use the flooring calculator →

On this page

  1. How to Work Out Trim
  2. Trim for Common Rooms
  3. Cope the Inside Corners
  4. What the Linear Feet Will Not Tell You
  5. Frequently Asked Questions

How to Work Out Trim

Running trim is a perimeter problem, not an area one. The floor can be any size; what matters is how far it is around the walls.

  1. Take the perimeter. For a rectangle, 2 × (length + width). For anything else, walk the walls and add the runs.
  2. Subtract the door openings — about 3 ft each including the jamb. Do this for baseboard and shoe; do not for crown, which runs past every door.
  3. Add waste — 10% for baseboard, coped inside corners included, and 15% for crown.
  4. Divide by your stock length and round up. Whole sticks only.

A 12 × 14 ft room with two doors: 52 ft of perimeter, less 6 ft of openings, is 46 linear ft. At 10% that is 51 ft, which is 5 pieces of 12 ft stock — 60 ft bought for 46 ft installed.

That gap between what you need and what you buy is not waste in the usual sense. It is the offcuts: the end of every stick that was too short to start the next wall.

Trim for Common Rooms

Baseboard, two 3 ft doorways deducted, 10% waste, 12 ft stock. Every figure is this calculator's own output:

RoomPerimeterNet Trim12 ft Pieces
8 × 10 ft36 ft30 ft3
10 × 12 ft44 ft38 ft4
12 × 14 ft52 ft46 ft5
12 × 20 ft64 ft58 ft6
16 × 20 ft72 ft66 ft7
20 × 24 ft88 ft82 ft8

For crown in the same rooms, do not deduct the doorways — add 6 ft back to the net figure — and use 15% waste instead of 10%. Across the rooms above that pushes crown a piece higher than baseboard in four cases out of six — the two it does not are where the extra length still fits inside the last stick.

Cope the Inside Corners

The single decision that separates trim that still looks right in five years from trim that does not.

Inside corners should be coped, not mitered. A mitered inside corner is two 45° cuts meeting at a point, and it relies on the wall being exactly 90° and staying there. Houses move, trim shrinks across its width as it dries, and the joint opens. Once it opens, caulk fills it for about a season.

A coped joint has the first piece run square into the corner and the second cut to the profile of the first, so it sits against its face. When the corner moves, the coped piece slides along the face of the other rather than pulling away from it. It takes longer to cut and it is far more forgiving.

Outside corners are mitered — there is no coping an outside corner. Those are the ones worth test-fitting on an offcut first, because outside corners are rarely the 90° the saw assumes.

A plain rectangular room has four inside corners. Every bump-out or chimney breast adds an inside and an outside corner, and the outside ones take the time.

What the Linear Feet Will Not Tell You

A total in linear feet assumes the offcut from one wall can start another. On long runs it can; on a room of short walls it often cannot, and that is the limit worth understanding before you buy.

If a single wall is longer than your stock length, no total can help you. A 15 ft wall in 12 ft stock needs either a scarf joint in the middle or a trip back for 16 ft material, and a joint in the middle of a long run shows however carefully it is cut. Measure the longest wall first, then pick the stock length; do not pick the stock length from the total.

Two other things the number leaves out:

Frequently Asked Questions

How much baseboard do I need?

Measure the room perimeter, subtract the door openings, then add waste for the miters. A 12 × 14 ft room has a 52 ft perimeter; take off two 3 ft doorways and you need 46 linear ft of baseboard, which at 10% waste is 51 ft — 5 pieces of 12 ft stock.

How do I calculate the perimeter of a room?

For a rectangle it is 2 × (length + width) — a 12 × 14 ft room is 2 × 26 = 52 ft. For an L-shaped or bayed room, walk the walls and add each run, then enter that total directly. Do not try to average an odd shape into a rectangle; trim follows the actual wall, not the floor area.

Do I subtract doorways from baseboard?

Yes for baseboard and shoe — the trim stops at the door casing on each side. No for crown molding, which runs continuously around the ceiling past every door. That one difference is why this calculator asks for the opening count separately: set it to zero when you are pricing crown.

How much extra trim should I buy?

10% for baseboard and shoe, coped inside corners included, and 15% for crown. The difference is the cut: a baseboard miter or cope wastes an inch or two, while a coped crown end is slow, easy to get wrong, and often worth a second attempt. Add more again if the profile has a strong pattern that has to line up across a joint.

What length trim should I buy?

Long enough to cross your longest wall in one piece if you can manage it. A joint in the middle of a long run always shows, however well it is cut, and a scarf joint in paint-grade trim will eventually telegraph. The trade-off is real though — 16 ft stock does not fit in most vehicles and is awkward to carry alone.

Why is my piece count higher than the linear feet suggest?

Because trim is bought in fixed lengths and offcuts are often not the right size for the next wall. Needing 51 linear ft does not mean four and a bit 12 ft sticks — it means five, because the leftover from each wall is usually too short to start another. The calculator rounds up to whole pieces for that reason.

Should I cope or miter an inside corner?

Cope it. A mitered inside corner opens up as the house moves and as the trim dries, and the gap that appears is impossible to fill invisibly. A coped joint has one piece cut square into the corner and the other cut to its profile, so it stays tight when the wall shifts. Outside corners are mitered — there is no alternative there.

How much door casing do I need?

Casing is counted per opening rather than around the perimeter, which is why it is not in the total above. A standard interior door takes roughly 17 linear ft to case one side — two legs at about 7 ft and a head at about 3 ft, before miter waste — so double it for a door cased on both faces. Count your openings and add it separately.

How many inside corners does a room have?

A plain rectangular room has four, and each one is a cope or a miter. Every bump-out, chimney breast or closet return adds two more — one inside and one outside. Corners are worth counting before you start because they, not the straight runs, are where the time goes.

Does the total linear feet tell me what to buy?

Only roughly, and this is the real limit of any trim calculator. A linear-feet total assumes the offcut from one wall can start the next one. If a single wall is longer than your stock length it needs a scarf joint or longer stock, and no total can tell you that — only a wall-by-wall list can. Measure your longest wall before you choose a stock length.

Do I need shoe molding as well as baseboard?

It depends on the floor. Shoe or quarter round covers the expansion gap that a floating floor needs at the wall, and it hides an uneven floor line that baseboard alone would show. If the baseboard goes on after the flooring and the floor is flat, you can skip it — but with laminate or vinyl plank the gap has to be covered by something that is not fastened to the floor.

Do I install baseboard before or after flooring?

After, in most cases. Laying the floor first lets the baseboard sit down onto it and hide the edge, and it means a floating floor can still move underneath. The exception is carpet, which is tucked under the baseboard — there the trim goes on first, held up off the subfloor by the thickness of the pad and carpet.

Estimates for planning only. Quantities are calculated from standard coverage and yield figures, with a waste allowance where the page states one. Always confirm against the manufacturer figures on the product you buy, and check local requirements before ordering. See our full method and assumptions.

Last updated · How we calculate