New concrete, or a surface the label rules out? Use sand for grip.
Use the sand calculator →On this page
How to Calculate Ice Melt
- Measure every surface you will treat. Driveway length × width, plus walks, steps and the porch.
- Convert to square yards. Divide square feet by 9. Many bag labels, including Morton’s and OxyChem’s, give their rate per square yard.
- Multiply by the rate on the bag. Use the low end for a thin glaze and the high end for thicker ice, or follow the conditions the label lists.
- Convert to what you buy. A rate in ounces or pounds converts straight to bags. A rate in cups needs the weight of a cup of your product; weigh one level cup.
- Multiply by the number of applications you expect over the winter.
Worked example: a 20 × 20 ft driveway plus 100 sq ft of walks is 500 sq ft, or 55.6 sq yd. At Morton’s 1/2 to 1 cup per square yard that is about 28 to 56 cups per application, which is 1.7 to 3.5 gallons by volume (16 cups to the gallon).
Label Rates from the Manufacturers
Application rates are printed on the bag, and they are lower than most people expect. These two come straight from the manufacturers’ own documents:
| Product | Label Rate | Basis |
|---|---|---|
| Morton Safe-T-Salt (rock salt) | 1/2 to 1 cup per sq yd after snowfall; 1/2 cup during snowfall on bare surfaces | Melts in normal winter temperatures, about 5°F and above |
| OxyChem calcium chloride | 14 to 28 lb per 1,000 sq ft (2 to 4 oz per sq yd) | Rate based on melting a thin sheet of ice at 20°F in 30 minutes |
Rates for other products, including magnesium chloride and blends, vary by brand, so choose Use the rate on my bag above and type in what yours says. Be wary of rates quoted online without a source: we have seen one that works out to roughly a hundred times these label rates.
| Area | Sq Ft | Sq Yd | Rock salt at 1/2–1 cup/sq yd | Calcium chloride at 2–4 oz/sq yd |
|---|---|---|---|---|
| Two-car driveway, 20 × 20 ft | 400 | 44.4 | 22–44 cups | 5.6–11.1 lb |
| Long single drive, 10 × 50 ft | 500 | 55.6 | 28–56 cups | 6.9–13.9 lb |
| Front walk, 4 × 30 ft | 120 | 13.3 | 7–13 cups | 1.7–3.3 lb |
| Steps and porch, about 60 sq ft | 60 | 6.7 | 3–7 cups | 0.8–1.7 lb |
How Cold Each Product Works
Each product has a temperature below which it stops being useful. Manufacturers state their own figures; these are Morton’s for its consumer range, from its product sheet:
| Product | Manufacturer’s Stated Limit |
|---|---|
| Morton Safe-T-Salt | Melts to 5°F |
| Morton Safe-T-Plus | Melts to 5°F |
| Morton Safe-T-Pet | Melts to 10°F |
| Morton Action Melt | Melts to −15°F |
| Morton Safe-T-Power | Melts to −25°F |
You will also see much lower “eutectic” temperatures quoted, such as about −28°F for magnesium chloride in the Texas Department of Transportation’s snow and ice manual. TxDOT describes it as the lowest temperature at which the chemical can melt snow or ice at all, and only at one exact concentration (21.6% for magnesium chloride). It is not the temperature at which a handful on your steps will clear ice in reasonable time. Use the figure on the bag.
Protecting Concrete, Brick and Pets
- New concrete: Morton’s label limits its rock salt to properly made, air-entrained concrete more than one year old. For a first-winter slab, use sand for grip instead (see the concrete driveway and concrete pages).
- Any concrete: the same label warns that all de-icers increase the number of freeze-thaw cycles, which can accelerate surface damage, and that poor-quality concrete of any age is at risk.
- Brick and flagstone: the label says not to use it on walks with mortar joints.
- Pets: the label warns that the cold from melting ice and snow can hurt paws.
- Slush: Morton’s directions say to remove slush or loose ice promptly once melting has occurred.
Ice Melt Mistakes to Avoid
- Spreading on deep snow. Shovel first. Morton’s directions say to remove loose snow, then sprinkle the de-icer.
- Doubling the dose. Stay within the label range. OxyChem advises starting at the minimum, and whatever you spread beyond that ends up in the lawn and on the concrete.
- Spreading by hand in clumps. An even layer works better; OxyChem recommends a spreader.
- Using the wrong product for the cold. Below a product’s stated limit, switch to one rated for lower temperatures rather than spreading more.
- Waiting for the first storm to buy. Work out the season’s need now.
Frequently Asked Questions
How much ice melt do I need for my driveway?
Work out the area in square yards (square feet ÷ 9) and multiply by the rate on the bag. Morton’s rock salt label says 1/2 to 1 cup per square yard, so a 20 × 20 ft driveway plus 100 sq ft of walks (500 sq ft, 55.6 sq yd) takes about 28 to 56 cups, or 1.7 to 3.5 gallons by volume, per application. A calcium chloride label at 2 to 4 oz per square yard comes to about 7 to 14 lb for the same area.
How much ice melt per square foot?
Far less than many people think. OxyChem’s calcium chloride guidance is 14 to 28 lb per 1,000 sq ft, which is 0.014 to 0.028 lb, about a quarter to half an ounce, per square foot. We have seen “3.1 pounds per square foot” quoted online; that would put about 1,550 lb on a 500 sq ft driveway, roughly a hundred times the label rate. Read the bag.
Does using more ice melt work faster?
The makers do not recommend it. OxyChem advises starting with the minimum recommended amount and spreading evenly with a spreader; Morton says melting should occur within 30 minutes at its label rate, after which you remove the slush.
Should I put ice melt down before it snows?
Morton’s directions give a lighter rate for that: during snowfall, spread 1/2 cup per square yard on bare surfaces to stop snow packing and sticking, then clear the snow as soon as it stops falling. After snowfall, clear the loose snow first, then apply 1/2 to 1 cup per square yard.
How cold is too cold for rock salt?
Morton describes its Safe-T-Salt rock salt as melting ice and snow in normal winter temperatures of about 5°F and above. For colder weather, manufacturers sell products with lower stated limits; Morton’s own line goes down to −15°F and −25°F. Those are the makers’ claims for their products, so check the bag you buy.
Will ice melt damage my concrete?
It can. Morton’s label warns that all de-icers increase the number of freeze-thaw cycles, which can accelerate surface damage, and says to use its rock salt only on properly made, air-entrained concrete more than one year old, and not on brick or flagstone walks with mortar joints. That matches the advice on our concrete driveway page: no chemical de-icers the first winter.
How do I convert cups of ice melt to pounds?
You need the weight of the product, and it varies between products, so weigh one level cup of yours on a kitchen scale and enter it above. Ounces per square yard convert exactly: 1 oz per sq yd is about 6.9 lb per 1,000 sq ft, which is why OxyChem’s 2 to 4 oz equals its 14 to 28 lb.
How many bags of ice melt do I need for the winter?
Multiply one application by the number of times you expect to treat. That number depends entirely on your winter, so the calculator asks for it rather than guessing; last year’s storms are the best guide.
Is sand better than ice melt?
Sand does not melt anything; it adds grip. That makes it the safer choice on concrete in its first winter and on surfaces a de-icer label rules out. Our sand calculator sizes it by area and depth.
Is ice melt safe for pets?
Morton’s rock salt label warns that cold from melting ice and snow can cause discomfort to pets’ paws, and the company sells a separate product it describes as safer for pets. If pets use the area, look for a product labeled for them and wipe paws after walks.
Sources & Standards
- Morton Safe-T-Salt product sheet and SDS — Label rate 1/2 to 1 cup per sq yd; melts at about 5 F and above; concrete and masonry warnings; Morton product-line melting claims
- OxyChem Calcium Chloride: Deicing Application Rate Guidance — 14 to 28 lb per 1,000 sq ft (2 to 4 oz per sq yd), based on melting a thin sheet of ice at 20 F in 30 minutes
- TxDOT Snow and Ice Control Operations Manual: Chemical Types — Eutectic temperatures of magnesium chloride, CMA and potassium acetate
Estimates for planning only. Quantities are calculated from standard coverage and yield figures, with a waste allowance where the page states one. Always confirm against the manufacturer figures on the product you buy, and check local requirements before ordering. See our full method and assumptions.