Still working out the floor itself?
Use the flooring calculator βOn this page
Pick the Profile From the Height Difference, Not the Name
There are five profiles, they are easy to confuse, and the one you need is decided almost entirely by one measurement: how far the new floor surface sits above or below whatever it meets.
Measure it with the new flooring in place — a plank laid loose on top of its underlayment, against the existing floor. Guessing from the plank thickness alone misses the underlayment, which is usually what pushes a flush joint into reducer territory.
| Height Difference | Profile | Where It Goes | Notes |
|---|---|---|---|
| Flush, or under about 1/8 in | T-molding | Two hard floors at the same height | Sits in a channel; needs a gap between the floors |
| About 1/8 to 3/8 in | Reducer | A hard floor meeting a lower one | Sloped top; the high side laps over |
| Over about 3/8 in | Reducer, or rebuild the substrate | A large step at a doorway | A step this size is a trip hazard, not a trim problem |
| Any, against carpet | Carpet edge or Z-bar | Hard floor meeting carpet | The carpet tucks into it; not the same part as a reducer |
| Any, floor just stops | End cap or threshold | Doorway to unfinished space, or an exterior door | Finishes an edge with nothing to meet |
| Stair edge | Stair nose | The front edge of every tread | Structural-ish: it takes the wear and the foot strike |
The 1/8 in figure is the usual limit, not a standard. A T-molding sits in a channel and has a finite amount of play; how much varies by manufacturer, and the spec sheet for the profile you are buying will say. Treat it as the point where you should stop assuming and start reading the box.
A step over about 3/8 in is worth solving properly. Self-leveler under the low side, or a plywood shim layer, is more work than buying a chunkier transition, but a lip that size is something people trip on for the life of the floor — see the self-leveling underlayment calculator if the low side is a slab.
Counting Pieces, Not Doorways
Transitions are sold in lengths — commonly 36, 72 or 94 in — and that length rarely matches a doorway, so the piece count is not the doorway count.
Four 36 in doorways do not need four pieces. A 94 in length cuts into two 36 in runs with 22 in left over, so four doorways take 2 pieces. The same four doorways at 48 in wide take 4 pieces, because only one 48 in run comes out of a 94 in length.
The lineal footage tells a different story from the piece count and both are worth knowing: four 36 in openings is 12 lineal feet of transition, which is what you would price if you were buying by the foot.
Buy at least one spare. A transition is cut to a finished length with a finished end; a miscut does not leave you an offcut for the next doorway, it leaves you short a whole piece. On stairs this matters more, because a stair nose is cut to the exact tread width and there is no forgiving end.
Stairs Are the Expensive Part
Every tread gets a stair nose, and that one part usually costs more per foot than the flooring it matches. A 13-tread flight at 36 in wide needs 13 nosings and 39 lineal feet — frequently more money than a small bedroom's worth of flooring, and it is the line most often missing from a first estimate.
Nosings needed and lengths bought are different numbers. Two 36 in treads come out of one 94 in length, so those 13 nosings are 7 lengths to buy. The calculator reports the lengths, because that is what goes in the cart.
The nosing has to span the full tread width in one piece. Two pieces butted mid-tread is both visible and a wear point, so the stock length has to be at least the stair width; a 36 in stair cannot use 36 in stock with no margin for a square cut.
Stair nosing also does real work. It takes the foot strike on every step, so it is fastened down properly — unlike a doorway transition on a floating floor, which must not be. Follow the manufacturer's fixing instructions for the nosing specifically rather than applying what you did in the field.
Before You Buy: Door Clearance and Level Changes
Check the doors first. Underlayment plus a floating floor commonly adds about 5/16 to 5/8 in of height, and plenty of interior doors have less clearance than that. Taking a door off and trimming the bottom is a twenty-minute job before the floor goes down and an awkward one afterwards. Check the swing over the highest point of the threshold, not the middle of the room.
Center the transition under the closed door so each room shows only its own floor when the door is shut.
Level changes are regulated in ways trim is not. Thresholds at exterior doors have height limits, and a change in level on an accessible route is governed separately from ordinary residential work. Both are adopted and amended locally. If a doorway is going to end up with a noticeable step — and particularly at an exterior door — check with your local code enforcement office or building department before you finish it. They are the authority that inspects the work, and a threshold is far cheaper to get right during the job than after it.
Frequently Asked Questions
How many transition strips do I need?
One run across every opening, but that is not the same as one piece per opening. Strips are sold in fixed lengths, and a 94 in length cuts into two 36 in doorways with 22 in left over. Four 36 in doorways need 2 pieces of 94 in stock, not 4. Add a spare, because a miscut wastes the whole length rather than an offcut.
What is the difference between a T-molding and a reducer?
Height. A T-molding is symmetrical and sits in a channel between two floors of the same height — roughly within 1/8 in. A reducer is sloped, and takes a hard floor down to a lower one. Fitting a T-molding across a real height difference leaves a lip that catches toes and eventually breaks the molding.
What transition do I use between tile and wood?
Measure the height difference first, because tile is usually the taller of the two. Flush or close to it takes a T-molding; the common case — tile sitting 1/4 in proud of the wood — takes a reducer running down from the tile. If the tile is more than about 3/8 in higher, the real fix is at the substrate, not the trim.
What goes between hard flooring and carpet?
A carpet edge — often called a Z-bar or carpet trim — not a reducer. Carpet needs something to tuck and grip into, which a reducer does not provide. The exception is where the hard floor sits noticeably higher than the carpet pad, where a reducer with a carpet edge is used together.
Do I need a stair nose on every tread?
Yes — one per tread, and it is the part that does the most work on the whole floor. A 13-tread flight needs 13 nosings, each spanning the full stair width in one unbroken piece. That is not the same as 13 lengths to buy: from 94 in stock, two 36 in treads come out of one length, so 13 nosings means 7 lengths. Stair nosing costs far more per foot than the flooring, and it is the single most underestimated line on a stair job.
Can one transition strip cover two doorways?
Yes, if the stock length allows. A 94 in length covers two 36 in doorways (72 in used, 22 in spare) but only one 48 in opening. That is why this calculator asks the opening width — it works out how many openings each length yields, rather than assuming one piece per door.
Will a new floor stop my door from closing?
It might, and it is the thing people forget until the floor is down. Adding underlayment plus a floating floor commonly raises the surface 1/2 to 3/4 in, and an interior door usually has less clearance than that. Check before you start: if the gap is tight, the door comes off and gets trimmed from the bottom, which is easier with the door already off than with a finished floor underneath it.
Where exactly should the transition sit in a doorway?
Centered under the closed door, so each room sees only its own flooring with the door shut. Putting it on one side of the jamb means the other room gets a stripe of the neighboring floor showing under the door.
Can I nail a transition strip down through a floating floor?
No. A floating floor has to move with humidity, and fastening anything through it pins it in place — which is what causes the buckling people blame on the flooring. The track or channel fastens to the subfloor within the expansion gap, and the visible strip clips into that. The laminate installation guide covers the sequence.
Is there a code limit on a step at a doorway?
There are limits on thresholds at exterior doors, and a change in level anywhere is a trip hazard that gets treated seriously in any inspected work. Residential rules differ from accessible-design rules, and both are amended locally. Check with your local code enforcement office or building department if a doorway is going to end up with a noticeable step, especially at an exterior door or on an accessible route — they are the authority that inspects it.
Should transitions match the floor or the trim?
The floor, and ideally from the same manufacturer and batch as the flooring itself. Most flooring lines sell matching profiles precisely because a near-match reads worse than a deliberate contrast. If you cannot match, a contrasting solid — often matched to the door or the baseboard — looks intentional in a way that an almost-right wood grain never does.
How much do transition strips cost?
They vary far too much by material and brand for this page to quote a number, and the site does not publish prices it cannot source. Put your own supplier price into the materials-cost box in the results and it will total the job. For a wider budget picture, the flooring cost guide covers where transitions sit among the other line items people leave off a first estimate.
Sources & Standards
- International Residential Code (ICC) β Residential construction requirements adopted by most US jurisdictions
- North American Laminate Flooring Association β Laminate performance standards (ANSI-accredited LF-01) and AC wear ratings
Estimates for planning only. The figures here follow published model codes and industry standards, but those are adopted and amended locally, and older buildings are often legally exempt from the current edition. Check with your local code enforcement office or building department before you order or build β they are the authority that inspects the work, and what they require overrides anything on this page. See our full method and assumptions.