📐 Floor and Depth
ft
The area you are pouring, not the whole room, if you are only leveling part of it.
ft
Together these give the area.
sq ft
Already measured, or an odd shape? This overrides the two boxes above.
in
The AVERAGE, not the deepest point. 1/8 in = 0.125, 1/4 in = 0.25, 1/2 in = 0.5.
cu ft
Printed on the bag. A 50 lb bag is commonly around 0.45 cu ft — check yours.
lb
For the total weight and the number of trips.
%
Material left in the bucket and the deep spots you underestimated.
✓ Results
Area 192 sq ft
Volume Needed 4 cu ft
Coverage per Bag at This Depth 21.6 sq ft
10 bags
Bags to Buy
Total Weight 500 lb
Water Needed (approximate) check the bag - measure it, do not judge by eye

Need a sloped bed rather than a level one?

Use the deck mud calculator →

On this page

  1. The Depth Is the Whole Problem
  2. Coverage by Depth
  3. Primer, Water and Dams
  4. When Not to Use It
  5. Frequently Asked Questions

The Depth Is the Whole Problem

Area is easy. Depth is the number that decides your order, and it is the one nobody hands you — a floor that needs leveling is by definition not a constant thickness.

Find the high spot first. The leveler has to cover it, so the high spot is your zero and everything else is measured down from it. Lay a long straightedge across the floor in a grid, measure the gap underneath at each position, and average those gaps. Then add whatever minimum thickness the product needs over the high point, because the material still has to flow across it.

Why this matters more than it looks. Bags scale linearly with depth across the entire floor. On a 192 sq ft room, being out by 1/8 in — a difference you cannot see — is 2 cubic feet of material, or about five extra bags. No other input on this page multiplies like that.

If the floor has one deep dip rather than a general slope, consider filling that dip with a patching compound first and leveling the rest thinly. Self-leveler is the expensive way to fill a hole.

Coverage by Depth

At a 0.45 cu ft bag yield and 10% waste. Coverage per bag is derived from the yield rather than quoted, because yield varies by product — it is an input for that reason. Every figure is this calculator's own output:

Average DepthDepth in FeetCoverage per Bag100 sq ft200 sq ft400 sq ft
1/8 in0.0104 ft43.2 sq ft3 bags6 bags11 bags
1/4 in0.0208 ft21.6 sq ft6 bags11 bags21 bags
3/8 in0.0313 ft14.4 sq ft8 bags16 bags31 bags
1/2 in0.0417 ft10.8 sq ft11 bags21 bags41 bags

Read down the 200 sq ft column: 6 bags at 1/8 in, 11 at 1/4 in, 21 at 1/2 in. Doubling the depth roughly doubles the order; the small differences are rounding up to whole bags. That is the entire argument for measuring the average properly instead of estimating it.

Primer, Water and Dams

Three things that are not in the bag count but decide whether the pour works.

Primer. Almost every product needs it and skipping it is a frequent cause of failure. A porous subfloor pulls water out of the mix before it can flow and level, and air escaping from below leaves pinholes across the surface. Primer stops both, and on wood it helps the bond as well. Twenty minutes, and the pour depends on it.

Water, measured. Self-leveler is far more sensitive to water than mortar or concrete. Too little and it will not flow out; too much and the aggregate settles, leaving a weak, dusty layer on top that has to be ground off. Measure the water into the bucket before the powder, and keep every batch identical — a floor mixed to varying consistencies sets in visible patches.

Dams. The material is liquid and it will find every gap: doorways, stair openings, floor vents, pipe penetrations, the gap under a wall plate. Seal them before you mix anything. A leak into the ceiling below is not a problem you get to fix later.

One more constraint worth planning around: working time is short, often in the region of ten to twenty minutes. Anything past about 100 sq ft needs two people and a mixing station ready before the first bag is opened, so each batch lands wet into the last.

When Not to Use It

Frequently Asked Questions

How much self-leveling underlayment do I need?

Multiply the area by the average depth in feet, then divide by the yield of one bag. A 16 × 12 ft floor at a 1/4 in average is 192 × 0.0208 = 4.0 cubic feet; at a 0.45 cu ft bag yield that is 9 bags, or 10 with waste. Yield is printed on the bag and varies by product, so use yours rather than a rule of thumb.

How do I work out the average depth?

This is the hard part, and it is where most estimates go wrong. Find the high spot first — the leveler has to cover it, so it sets your zero. Then lay a long straightedge across the floor in a grid and measure the gap under it at each point. Average those gaps and add the minimum thickness the product needs over the high spot. Guessing this number is the single biggest cause of a short order.

Why does a small depth error cost so many bags?

Because bags scale linearly with depth over the whole floor. On 192 sq ft, being out by just 1/8 in is 2 cubic feet of material — about five extra bags. Depth is the only input where a small mistake multiplies across the entire area, which is why it is worth measuring properly rather than eyeballing.

What is the minimum thickness for self-leveler?

Most products have both a minimum and a maximum per pour, and both are on the bag — a common minimum is around 1/8 in, because thinner than that the material cannot flow and level properly. There is also usually a maximum single lift; deeper than that has to be built up in layers with the manufacturer’s waiting time between them. Check the bag rather than assuming.

Do I need primer under self-leveler?

Almost always, yes, and skipping it is a frequent cause of failure. Primer does two jobs: it stops a porous subfloor sucking the water out of the mix before it can flow and level, and it stops pinholes forming as air escapes from below. On wood subfloors it also helps the bond. It is cheap, it takes twenty minutes, and without it the pour can fail outright.

How much water does self-leveler need?

Exactly what the bag says, measured — not judged by eye. Self-leveler is far more sensitive to water than mortar or concrete: too little and it will not flow, too much and the aggregate settles out, leaving a weak, dusty surface that has to come back up. Measure the water into the bucket before the powder goes in, and keep every batch identical.

Can I pour self-leveler over plywood?

Over a sound, well-fastened wood subfloor, yes — with the right primer and usually with the product rated for it. The subfloor has to be stiff: self-leveler is rigid, and it will crack over a floor that flexes underfoot. Screw down every loose spot before you pour, because you cannot fix deflection with a topping.

Self-leveler or deck mud?

Different tools for different jobs. Self-leveler is pourable, finds its own level, and is for flattening a floor that should be flat. Deck mud is a packed, dry mix you screed to a deliberate slope — a shower pan is supposed to fall toward the drain, and a self-leveler physically cannot do that. Our deck mud calculator covers the sloped case.

Do I need to dam the edges?

Yes, anywhere the material could escape — doorways, stair openings, floor vents, pipe penetrations and the gap under a wall plate. Self-leveler is liquid and it will find every hole you did not think about, including ones that drain into the ceiling below. Foam backer rod, expanding foam or timber battens all work; do it before you mix, not while it is flowing.

How long do I have to work with it?

Not long — typically in the region of ten to twenty minutes, and it is on the bag. That is the real constraint on a big floor: you cannot mix a batch, pour it, and then start thinking about the next one. Anything over about 100 sq ft wants two people and a mixing station set up before the first bag is opened, so pours land wet into wet.

How many bags for a 200 square foot floor?

At a 1/4 in average depth and a 0.45 cu ft bag, 11 bags including 10% waste. At 1/8 in it is 6; at 1/2 in it is 21. The depth doubles the order each time it doubles, which is why the averaging exercise is worth doing carefully.

Can I walk on it, and when?

Most products take foot traffic within a few hours and accept flooring after a longer wait that depends on the product and on what is going down — a vapor-sensitive floor covering may need a moisture test first. Both figures are on the bag. Do not rush the flooring: trapping moisture under an impermeable covering causes failures that appear months later.

Estimates for planning only. Quantities are calculated from standard coverage and yield figures, with a waste allowance where the page states one. Always confirm against the manufacturer figures on the product you buy, and check local requirements before ordering. See our full method and assumptions.

Last updated · How we calculate