Caulking as part of an exterior repaint?
Use the exterior paint calculator →On this page
How Much Caulk You Need
Caulk is sold by volume and applied as a bead, so the whole calculation turns on the size of that bead — and the bead is squared, which catches people out.
- Cross-section = width × depth. A 1/4 × 1/4 in joint is 0.0625 sq in.
- Tube volume. One US fluid ounce is 1.8047 cubic inches, so a standard 10.1 fl oz cartridge holds 18.2 cu in.
- Divide. 18.2 ÷ 0.0625 = 291 inches, or 24.3 linear ft per tube.
- Add waste — 15% covers purging the nozzle, the part-used tube that skins over, and the one that gets dropped.
So 120 linear ft of 1/4 in joint takes 6 tubes.
The squaring is the part worth internalizing. Going from a 1/4 in bead to a 1/2 in bead doubles the width but quadruples the volume — the same tube drops from 24 ft to 6. If you are getting through cartridges faster than you expected, the bead is almost always bigger than you think.
Coverage per Tube
Linear feet from one tube, derived from the bead section rather than quoted. Every figure is this calculator's own output:
| Bead Size | Cross-Section | 10.1 fl oz | 5.5 fl oz | 28 fl oz |
|---|---|---|---|---|
| 1/8 × 1/8 in | 0.0156 sq in | 97.2 ft | 52.9 ft | 269.5 ft |
| 3/16 × 3/16 in | 0.0352 sq in | 43.2 ft | 23.5 ft | 119.8 ft |
| 1/4 × 1/4 in | 0.0625 sq in | 24.3 ft | 13.2 ft | 67.4 ft |
| 3/8 × 3/8 in | 0.1406 sq in | 10.8 ft | 5.9 ft | 29.9 ft |
| 1/2 × 1/2 in | 0.25 sq in | 6.1 ft | 3.3 ft | 16.8 ft |
The 1/4 × 1/4 in row is the one most people work to, and 24.3 ft is where the trade rule of thumb — "about 25 feet a tube" — comes from.
Which Caulk for Which Job
Using the wrong type is a more expensive mistake than buying the wrong amount, because you find out a season later.
| Type | Use It For | Paintable? | Cleanup | Do Not Use For |
|---|---|---|---|---|
| Acrylic latex (painter’s caulk) | Interior trim, gaps before painting | Yes | Water | Outdoors, or any joint that moves |
| Siliconized acrylic | Interior trim, light moisture | Usually | Water | Constant wet |
| 100% silicone | Showers, tubs, glass, non-porous | No | Mineral spirits | Anything you will paint |
| Polyurethane | Exterior joints, concrete, high movement | Yes | Mineral spirits | Indoor trim — overkill and messy |
| Butyl rubber | Gutters, flashing, roof details | Poorly | Mineral spirits | Anywhere visible — it stays tacky |
The two that matter most. Painter’s caulk outdoors is the classic error — it is cheap, it tools beautifully, and it splits within a season or two once it is in the weather. And 100% silicone under paint is the other: paint beads up and peels off it, no primer fixes it, and the only cure is cutting the silicone out and starting again.
Where a joint passes through a fire-rated assembly, none of the above applies — firestop sealants are tested and listed as assemblies, and that is a code matter for your local code enforcement office.
Joint Design: the 2:1 Rule and Backer Rod
This is the part that decides whether a joint lasts five years or five months, and it is missing from most caulk advice.
Depth should be about half the width — 1/4 in deep in a 1/2 in joint — with 1/4 in a practical minimum and 1/2 in a maximum. A bead deeper than it is wide behaves like a rigid plug: it cannot stretch, so the first time the joint opens it tears away from one face.
The bead must bond to two faces, not three. If caulk touches the back of the joint as well as both sides, it is anchored on three surfaces and physically cannot stretch. It splits. Backer rod — foam rope pushed in before caulking — solves both problems at once: it sets the depth, and it gives the caulk something to sit against that it will not bond to.
Use backer rod in any joint deeper than it is wide, which is the point where the bead would otherwise become a rigid plug. Where there is no room for rod, bond-breaker tape along the back of the joint does the same job.
Application and Cleanup
Before you start
- Remove every trace of the old caulk. New caulk does not bond to cured caulk, and nothing at all bonds to cured silicone — including more silicone.
- Clean and dry the faces. Scrape, then wipe non-porous surfaces with isopropyl alcohol. Caulk over dust is caulk stuck to dust.
- Check the temperature range on the tube and the forecast. Most sealants need dry surfaces and a minimum temperature, and rain within a few hours of application will ruin an exterior bead.
- Cut the nozzle small and at 45°, then test on cardboard. You can always cut it bigger; you cannot make it smaller.
Laying the bead
- Push the gun, do not pull it. Pushing forces material into the joint; pulling lays a bead over the top and leaves voids underneath.
- Keep moving at a steady speed with even trigger pressure. Stopping mid-run leaves a lump you will have to tool out.
- Tool it once, promptly. One pass, pressing the bead against both faces into a slightly concave profile. Going back over a bead that has skinned tears it instead of smoothing it.
- A wet finger is fine for latex. Use a tool or a soapy finger for silicone, which grabs skin and strings.
Cleanup
- Latex and siliconized acrylic — warm water and a damp rag, while wet.
- Silicone — mineral spirits or isopropyl alcohol, immediately. Once cured it has to be cut out.
- Polyurethane — mineral spirits straight away, and keep it off skin and clothing. Cured polyurethane is effectively permanent.
- Have the rag and the solvent in your hand before the first squeeze, not after. Every one of these is easy wet and miserable dry.
- Cap the tube with a nail or the cap it came with. A skinned cartridge is a wasted one, which is most of what the 15% waste allowance is paying for.
Caulking Mistakes to Avoid
- Caulking what should drain. The bottom edge of lap siding, brick weep holes and the gap under a sill pan are drainage paths. Sealing them traps water in the wall.
- Painter’s caulk outdoors. It splits within a season or two. Use polyurethane or an exterior-rated sealant.
- Filling a deep joint solid. Three-sided adhesion means it cannot stretch. Backer rod first.
- Cutting the nozzle too big. A bead twice as wide uses four times the material and looks worse.
- Tooling twice. The second pass tears a skinning bead.
- Caulking over old caulk or a wet surface. Both fail at the bond line, and both look fine for about a month.
Frequently Asked Questions
How many feet does a tube of caulk cover?
It depends entirely on the bead size. A standard 10.1 fl oz cartridge holds 18.2 cubic inches, so at a 1/4 × 1/4 in bead it runs about 24 linear feet. Double the bead to 1/2 × 1/2 in and the same tube gives you barely 6 ft — four times the volume for twice the width, because the section is squared.
How do I work out how much caulk I need?
Multiply the joint width by the depth to get the cross-section in square inches, then divide the tube volume by it. A 10.1 oz tube is 18.2 cu in; a 1/4 × 1/4 in joint is 0.0625 sq in; 18.2 ÷ 0.0625 = 291 inches, or 24.3 ft. Then divide your total joint length by that and add waste — 120 ft of 1/4 in joint needs 6 tubes.
How deep should a caulk joint be?
About half the width, with 1/4 in as a practical minimum and 1/2 in as a maximum. A bead deeper than it is wide cannot stretch — it behaves like a rigid plug and tears away from one side the first time the joint moves. This is why filling a deep gap to the bottom with caulk fails, and why backer rod exists.
What is backer rod and do I need it?
A foam rope pushed into a deep joint before caulking. It does two jobs: it sets the depth of the bead, and it stops the caulk bonding to the back of the joint. A bead stuck to three faces cannot move — it has to stretch and it cannot, so it splits. Bonded to two faces only, it flexes with the joint. Use it in any joint deeper than it is wide.
What type of caulk should I use?
Match it to the job. Acrylic latex for interior trim you are going to paint. 100% silicone for showers, tubs and anything permanently wet — but it will not take paint. Polyurethane for exterior joints that move, and for concrete. Butyl for gutters and flashing. A frequent mistake is using painter’s caulk outdoors, where it splits within a season or two.
Can you paint over silicone caulk?
No — not reliably, and not for long. Paint beads up on 100% silicone and peels off it, and no primer fixes that properly. If the joint has to be painted, use an acrylic latex or a siliconized acrylic and check the tube says paintable. If silicone is already there and you need paint, it has to be cut out, not covered.
How do you clean up caulk?
It depends on the type, and it has to be done while the caulk is wet. Acrylic latex cleans up with water and a damp rag. Silicone and polyurethane need mineral spirits or isopropyl alcohol, and both are extremely difficult once cured — cured polyurethane usually has to be cut off. Keep a rag and your solvent in hand before you pull the trigger, not after.
Should you push or pull the caulk gun?
Push it. Pushing forces caulk into the joint ahead of the nozzle and fills it; pulling drags a bead across the top and leaves voids underneath that you cannot see. The exception is a very narrow joint where pushing piles material up — there, pull slowly. Either way, keep the gun at roughly 45° and move at a steady speed.
How do you tool a caulk joint?
Once, promptly, and in one pass. Tooling presses the bead against both faces — which is what makes it bond — and leaves a slight concave profile that can stretch. A wet finger works for latex; use a proper tool or a soapy finger for silicone, because silicone grabs skin. Going back over a skinned bead tears it rather than smoothing it.
Do you have to remove old caulk first?
Yes, all of it. Fresh caulk does not bond to cured caulk — least of all to silicone, which nothing sticks to, including more silicone. Cut it out with a utility knife or a caulk removal tool, scrape the faces clean, and wipe non-porous surfaces with alcohol. Caulking over a failed bead buys a few months at most.
What should you NOT caulk?
Anything that is meant to drain or breathe. The bottom edge of lap siding, weep holes in brick, the gap under a window sill pan, and the horizontal joints a siding manufacturer tells you to leave open are all drainage paths. Sealing them traps water inside the wall, which is far worse than the draft you were trying to stop.
Does fire-rated caulk matter?
Where a joint or a penetration passes through a fire-rated assembly, the sealant is part of the rated system and an ordinary tube of caulk is not a substitute. Firestop products are tested as assemblies and installed to a listing. That is a code matter — check with your local code enforcement office or building department, which is the authority that inspects it.
Estimates for planning only. Quantities are calculated from standard coverage and yield figures, with a waste allowance where the page states one. Always confirm against the manufacturer figures on the product you buy, and check local requirements before ordering. See our full method and assumptions.