Painting the fence or trim instead?
Use the exterior paint calculator →On this page
How to Calculate Stain
- Measure the surfaces. Deck floor: length × width. Fence: length × height, per side. Add railings, stairs and built-in benches as extra area.
- Read the coverage off the can. It is usually given as a range; use the low end for rough-sawn or weathered wood and the high end for smooth new boards.
- Divide area by coverage for the first coat.
- Add the second coat if the product calls for one. A second coat goes on sealed wood and spreads further; Behr’s acrylic sheet lists twice the first-coat coverage.
- Round up to whole gallons.
Worked example: a 20 × 16 ft deck is 320 sq ft. At 250 sq ft per gallon, one coat is 1.28 gallons, so buy 2.
Stain Coverage from Manufacturer Data Sheets
Coverage is the number most stain estimates get wrong, because it varies so much. These are the figures printed on four widely sold products’ technical data sheets:
| Product | Type | Coverage per Gallon |
|---|---|---|
| Behr Premium Semi-Transparent Penetrating Oil | Semi-transparent, oil | 350–400 sq ft/gal |
| Behr Premium Semi-Transparent (acrylic) | Semi-transparent, two coats | 1st coat 250–300; 2nd coat 500–600 |
| Sherwin-Williams SuperDeck Semi-Transparent | Semi-transparent, one coat | 150–350 sq ft/gal |
| Sherwin-Williams SuperDeck Solid Color | Solid color | New wood 350–400; weathered 250–300 |
Across these four the spread is 150 to 400 sq ft per gallon for a first coat, which is more than double. This calculator defaults to 250. That sits inside the Behr acrylic and SuperDeck semi-transparent ranges and the solid stain’s weathered-wood range, and below the oil stain and new-wood figures, so for those products it errs toward buying extra. Either way, the coverage on your can is the one to use. Products are reformulated, so read the current label rather than trusting a table, including this one.
Stain for Common Decks and Fences
Gallons at 250 sq ft per gallon for the first coat and 500 for a second coat:
| Project | One Coat (gal) | Two Coats (gal) | Buy (two coats) |
|---|---|---|---|
| 12 × 12 ft deck (144 sq ft) | 0.58 | 0.86 | 1 gal |
| 16 × 20 ft deck (320 sq ft) | 1.28 | 1.92 | 2 gal |
| 20 × 24 ft deck (480 sq ft) | 1.92 | 2.88 | 3 gal |
| 100 ft × 6 ft fence, one side (600 sq ft) | 2.40 | 3.60 | 4 gal |
| 100 ft × 6 ft fence, both sides (1,200 sq ft) | 4.80 | 7.20 | 8 gal |
Add railings and stairs on top.
Staining Mistakes to Avoid
- Using the best-case coverage. Data sheets give a range “depending on porosity and texture”; rough, weathered boards land at the low end.
- Over-applying a penetrating stain. What the wood cannot absorb stays on the surface; Sherwin-Williams warns it can look glossy and remain tacky. Back-brush and wipe off puddles.
- Mixing batches mid-job. Box several cans together before starting.
- Staining in direct sun. Every data sheet we checked gives a temperature window, with a low limit between 35 and 50°F and a high of 90°F. Most also warn against hot surfaces or direct sun, and against staining with rain on the way.
- Forgetting the fence’s second side. If you share the fence, agree who stains which face before you buy.
Building before staining? The deck boards calculator and fence calculator size the lumber.
Frequently Asked Questions
How much stain do I need for my deck?
Multiply length × width for the floor area, add railings and stairs, then divide by the coverage on the can. A 20 × 16 ft deck is 320 sq ft; at 250 sq ft per gallon that is 1.28 gallons for one coat, so buy 2 gallons. Rough or weathered boards soak up more, so use the low end of the can’s range for an old deck.
How many square feet does a gallon of deck stain cover?
It depends on the product and the wood. On the data sheets we checked, semi-transparent stains ranged from 150 to 400 sq ft per gallon and a solid color stain from 250 (weathered wood) to 400 (new wood). Sherwin-Williams gives 150 to 350 for its SuperDeck semi-transparent, “depending on porosity and texture”. The figure on your can beats any average.
Do I need one coat of stain or two?
Follow the product. Some are one-coat stains; Sherwin-Williams lists “one coat only coverage on exterior woods” for its SuperDeck semi-transparent. Others require two thin coats; Behr’s acrylic semi-transparent asks for two, with the second covering about twice the area of the first because the wood is already sealed. Piling on extra coats of a penetrating stain does not add protection: what the wood cannot absorb stays tacky on the surface.
How much stain do I need for a fence?
Fence area is length × height, per side. A 100 ft run of 6 ft fence is 600 sq ft on one side and 1,200 sq ft for both. At 250 sq ft per gallon that is 2.4 or 4.8 gallons for one coat. Board-on-board and shadowbox fences expose more edge and overlap, so allow more than the flat figure.
Why does old wood take more stain?
Weathered wood is more porous. The fibers at the surface have been broken down by sun and water, so they absorb more. Sherwin-Williams’ solid color data sheet, for example, gives 350 to 400 sq ft per gallon on new wood but only 250 to 300 on weathered wood.
How do I estimate railing area?
Treat each side of the railing as a solid panel, length × height, and double it for both faces. That overstates a baluster railing, which is mostly air, but balusters have four faces each and eat stain, so the generous figure is safer than an exact one. Stairs: count each tread and riser as a rectangle.
Should I buy 1-gallon cans or a 5-gallon pail?
For more than a few gallons, one batch is easier to keep consistent: colors can drift slightly between cans, so if you do buy several cans, mix them together (called boxing) before you start. The calculator shows the total both ways so you can compare.
Is deck stain the same as paint for coverage?
No. Paint forms a film and covers a fairly predictable 350 to 400 sq ft per gallon on smooth surfaces, while stain soaks in, so the wood decides how far it goes. For painted fences and trim, use the exterior paint calculator.
Does the gap between deck boards change how much stain I need?
Not in a way worth calculating. The gaps remove a little face area, but you also stain the board edges where the brush or pad reaches, and either difference is small next to the spread in coverage between products. Use the full length × width.
Sources & Standards
- BEHR PREMIUM Semi-Transparent Penetrating Oil Stain & Sealer data sheet — Coverage 350-400 sq ft/gal; application temperature 40-90 F
- BEHR PREMIUM Semi-Transparent Waterproofing Stain & Sealer (acrylic) data sheet — Two thin coats; spread rate 250-300 sq ft first coat, 500-600 second coat
- Sherwin-Williams SuperDeck Exterior Semi-Transparent Wood Stain-250 data sheet (114.803) — Coverage 150-350 sq ft/gal depending on porosity and texture; one coat
- Sherwin-Williams SuperDeck 9600 Solid Color Acrylic-Alkyd Stain data sheet (114.96) — Coverage 350-400 sq ft/gal on new wood, 250-300 on weathered wood
Estimates for planning only. Quantities are calculated from standard coverage and yield figures, with a waste allowance where the page states one. Always confirm against the manufacturer figures on the product you buy, and check local requirements before ordering. See our full method and assumptions.