📐 Your Measurements
1/16 in matches most tape measures.
ft
in
ft
in
ft
in
ft
in
ft
in
How many times, or how many pieces.
in
The width of wood the blade removes: about 1/8 in for a full-kerf blade, less for a thin-kerf one. Check your blade. Used only for equal pieces.
✓ Results
9 ft 5 1/8 in
Feet, Inches and Fraction
Inches Only 113 1/8 in
Decimal Inches 113.125 in
Decimal Feet 9.4271 ft
Millimeters 2,873.4 mm
Meters 2.873 m
Rounding Exact to 1/16 in

On this page

  1. How to Add Feet and Inches
  2. How to Read a Tape Measure
  3. Fraction to Decimal Chart
  4. Inches to Decimal Feet
  5. Dividing Into Equal Parts and Cutting Pieces
  6. Converting to Metric
  7. Mistakes That Throw a Measurement Off
  8. Frequently Asked Questions

How to Add Feet and Inches

Work right to left, the way you add any numbers with carrying: fractions, then inches, then feet. Every 12 inches you carry becomes a foot, and every whole inch you collect from the fractions joins the inches.

  1. Put the fractions over the same bottom number. 3/8 and 3/4 become 3/8 and 6/8.
  2. Add the fractions. 3/8 + 6/8 = 9/8, which is 1 1/8 in. Carry the 1 to the inches.
  3. Add the inches. 7 + 9 + 1 = 17 in, which is 1 ft 5 in. Carry the foot.
  4. Add the feet. 5 + 3 + 1 = 9 ft.
  5. Read the answer. 5 ft 7 3/8 in + 3 ft 9 3/4 in = 9 ft 5 1/8 in.

The other way is to turn everything into inches first (5 ft 7 3/8 in is 67.375 in, 3 ft 9 3/4 in is 45.75 in), add them to get 113.125 in, and convert back: 113.125 ÷ 12 = 9 ft with 5.125 in left over. The calculator works this way, which is why it can also show decimal inches, decimal feet and millimeters for the same answer.

Subtracting works the same in reverse. When the inches on top are smaller, borrow a foot as 12 inches: 10 ft 2 in − 3 ft 8 1/2 in becomes 9 ft 14 in − 3 ft 8 1/2 in = 6 ft 5 1/2 in.

How to Read a Tape Measure

One inch of a tape measure, enlarged An enlarged inch of tape measure from the 1 inch mark to the 2 inch mark, divided into sixteen spaces. The half-inch line is longest, then quarter, eighth and sixteenth lines. The sixth mark past 1 inch is highlighted as 1 3/8 inches. 1 2 1/161/81/41/23/4 6 marks past 1 in = 1 6/16 = 1 3/8 in Longest line: 1/2. Then 1/4 and 3/4, then eighths, then sixteenths.
Fig. 1 — One inch of tape, enlarged. The longer the line, the simpler the fraction: the half is longest, then the quarters, the eighths and the sixteenths. Six marks past 1 in reads 1 6/16 in, which is 1 3/8 in.

An inch on most US tapes is divided into 16 equal spaces. The marks are drawn at different lengths so you can tell them apart without counting every one: the longer the line, the simpler the fraction it marks.

To read a measurement, note the last whole inch, count the sixteenths past it, and reduce the fraction. Six marks past 1 in is 1 6/16 in, which reduces to 1 3/8 in (1.375 in). Some tapes print the first few inches in 1/32 in for finer work.

The hook on the end slides by its own thickness on purpose, so an inside measurement (hook pushed in) and an outside one (hook pulled over an edge) both read true. If the rivets are loose or the hook is bent, the first inch is wrong on every reading.

Fraction to Decimal Chart

Every sixteenth of an inch as a decimal and in millimeters. The millimeter column is exact, because the inch is defined as 25.4 mm.

FractionDecimal InchesMillimeters
1/16 in0.0625 in1.5875 mm
1/8 in0.125 in3.175 mm
3/16 in0.1875 in4.7625 mm
1/4 in0.25 in6.35 mm
5/16 in0.3125 in7.9375 mm
3/8 in0.375 in9.525 mm
7/16 in0.4375 in11.1125 mm
1/2 in0.5 in12.7 mm
9/16 in0.5625 in14.2875 mm
5/8 in0.625 in15.875 mm
11/16 in0.6875 in17.4625 mm
3/4 in0.75 in19.05 mm
13/16 in0.8125 in20.6375 mm
7/8 in0.875 in22.225 mm
15/16 in0.9375 in23.8125 mm
1 in1 in25.4 mm

For a fraction that is not a sixteenth, divide the top number by the bottom: 5/32 is 5 ÷ 32 = 0.15625 in. To go the other way, multiply the decimal by 16 and round to the nearest whole number for sixteenths: 0.4 × 16 = 6.4, so 0.4 in is about 6/16 = 3/8 in.

Inches to Decimal Feet

Plans, laser measures and spreadsheets often use decimal feet. Divide inches by 12 to convert:

InchesDecimal FeetMillimeters
1 in0.0833 ft25.4 mm
2 in0.1667 ft50.8 mm
3 in0.25 ft76.2 mm
4 in0.3333 ft101.6 mm
5 in0.4167 ft127 mm
6 in0.5 ft152.4 mm
7 in0.5833 ft177.8 mm
8 in0.6667 ft203.2 mm
9 in0.75 ft228.6 mm
10 in0.8333 ft254 mm
11 in0.9167 ft279.4 mm

A common slip is reading 5.6 ft as 5 ft 6 in. It is 5 ft 7.2 in, because 0.6 ft × 12 = 7.2 in. Whenever a measurement has a decimal point, check whether it is decimal feet or inches before you cut.

Dividing Into Equal Parts and Cutting Pieces

Spacing posts, balusters or shelf brackets evenly is pure division: 10 ft 4 in split into 4 equal spaces is 124 ÷ 4 = 31 in each.

Cutting a board into equal pieces is different, because the saw blade removes wood with every cut. A full-kerf blade takes about 1/8 in and a thin-kerf blade about 3/32 in; many circular-saw blades are thinner still. Check the kerf printed on your blade or its packaging and enter that. Three pieces need two cuts, so:

Piece length = (Board length − (Pieces − 1) × Kerf) ÷ Pieces

For an 8 ft board in three pieces with a 1/8 in kerf, that is (96 − 0.25) ÷ 3 = 31.917 in. Rounded to the nearest sixteenth it would be 31 15/16 in, and three of those plus two kerfs come to 96.06 in, longer than the board. The calculator rounds equal pieces down instead, to 31 7/8 in, so all three fit.

Converting to Metric

The conversion is exact: 1 in = 25.4 mm and 1 ft = 304.8 mm, by the international definition adopted in 1959. A 2,400 mm sheet is 94.49 in, about 7 ft 10 1/2 in; a 600 mm cabinet is 23.62 in, about 23 5/8 in. Metric sheet goods and imperial framing do not line up exactly, so measure the actual sheet before you set out a cut list from a metric size.

Mistakes That Throw a Measurement Off

For an area or a volume rather than a length, use the square footage calculator or the cubic yard calculator. Both take feet as decimals, so convert feet-and-inches here first.

Frequently Asked Questions

How do I add feet and inches?

Add the inches and fractions first, then the feet, and carry every 12 inches over as a foot. 5 ft 7 3/8 in + 3 ft 9 3/4 in: the fractions make 3/8 + 6/8 = 1 1/8 in, the inches 7 + 9 + 1 = 17 in, which is 1 ft 5 in, and the feet 5 + 3 + 1 = 9. The answer is 9 ft 5 1/8 in. The calculator above does the carrying for up to four lengths.

How do I subtract feet and inches?

Subtract the fractions, then the inches, then the feet, and borrow a foot (12 in) when the inches on top are smaller. 10 ft 2 in − 3 ft 8 1/2 in: borrow a foot to make 9 ft 14 in, then 14 − 8 1/2 = 5 1/2 in and 9 − 3 = 6 ft, so 6 ft 5 1/2 in. Set Length 2 to − in the calculator to do it there.

How many inches are in a foot?

12. A yard is 3 ft or 36 in. To turn inches into feet, divide by 12: 67 in ÷ 12 = 5.58 ft, which is 5 ft 7 in.

How do I convert decimal feet to feet and inches?

Keep the whole number as feet, multiply the decimal part by 12 for inches, then multiply what is left after the decimal point by 16 for sixteenths. 7.45 ft: 0.45 × 12 = 5.4 in, and 0.4 × 16 = 6.4, which rounds to 6/16 = 3/8. So 7.45 ft is 7 ft 5 3/8 in, about 1/40 in under the exact length.

What is 5/8 inch as a decimal?

0.625 in, which is 15.875 mm. Any fraction converts by dividing the top number by the bottom: 5 ÷ 8 = 0.625. The fraction to decimal chart above lists every sixteenth.

How many millimeters are in an inch?

Exactly 25.4. The inch has been defined as 25.4 mm since the 1959 international yard agreement, so the conversion has no rounding in it. A foot is 304.8 mm and 1/16 in is 1.5875 mm.

What do the lines on a tape measure mean?

Most US tapes split each inch into 16 parts, and the length of each line tells you which fraction it marks: the longest line inside the inch is 1/2, then 1/4 and 3/4, then the eighths, and the shortest lines are the sixteenths. Count sixteenths past the last whole inch and reduce: 6 lines past the 1 in mark is 1 6/16 in, which is 1 3/8 in.

What are the red numbers and black diamonds on a tape measure?

Highlighted numbers every 16 in mark stud spacing for wall framing, and the small black diamonds every 19.2 in mark a joist or truss layout that fits five spaces into each 8 ft (96 ÷ 5 = 19.2). Not every brand prints both, so check yours.

How do I divide a length into equal parts?

Without cutting, just divide: 10 ft 4 in into 4 equal spaces is 124 ÷ 4 = 31 in each. When you are cutting a board into pieces, take the blade width out first, because every cut turns the blade’s width into sawdust (about 1/8 in for a full-kerf blade): an 8 ft board into 3 pieces with two 1/8 in cuts gives (96 − 0.25) ÷ 3 = 31.92 in, so cut each at 31 7/8 in. Round down, never up, or the last piece comes up short. The calculator’s equal-pieces option does this.

How do I multiply feet and inches?

Convert to inches, multiply, then convert back. Six pieces of 2 ft 7 1/2 in is 31.5 in × 6 = 189 in, which is 15 ft 9 in of material before any allowance for cuts or waste.

Why does my answer say it was rounded?

A decimal or metric measurement rarely lands on a tape mark. The rounding line shows how far the nearest fraction is from the exact length, so you can decide whether the difference matters. 7.45 ft rounds to 7 ft 5 3/8 in, which is 0.025 in (0.64 mm) short: nothing on a fence rail, but enough to notice on a cabinet face frame. Pick 1/32 or 1/64 in for finer work.

How do I convert millimeters to feet and inches?

Divide by 25.4 for inches, then by 12 for feet. 2,400 mm ÷ 25.4 = 94.49 in, which is 7 ft 10.49 in, or 7 ft 10 1/2 in to the nearest sixteenth. Choose millimeters as the unit in the calculator to do it there.

Sources & Standards

Estimates for planning only. Quantities are calculated from standard coverage and yield figures, with a waste allowance where the page states one. Always confirm against the manufacturer figures on the product you buy, and check local requirements before ordering. See our full method and assumptions.

Last updated · How we calculate