Ice Dams: What Causes Them and How to Prevent Them

An ice dam is a ridge of ice along the eaves that holds back melting snow. The water behind it can back up under the shingles and into the ceiling and walls. Ice dams form when heat from the house melts snow on the upper roof and the water refreezes at the cold edge, so the lasting fix is to keep that heat out of the attic. This guide covers why they form, the permanent fix in the order that matters, what to do about one that is leaking now, and where heat cable and eave membrane fit in.

How an Ice Dam Forms

How an ice dam forms Roof cross-section. Warm air leaks up through the ceiling into the attic and warms the roof deck, melting the snow above. Melt water runs down to the cold overhang and freezes into an ice ridge, with a pool of water behind it backing up under the shingles. An ice barrier membrane covers the deck from the roof edge to 24 inches inside the exterior wall line. 24 in inside the wall line Warm air leaks through the ceiling into the attic and warms the roof deck Fix: air seal, insulate, ventilate Snow melts on the warm upperroof, above 32Β°F Ice dam over the cold overhang Water pools behind it, under the shingles Ice barrier membrane (thick line on the deck) wall
Fig. 1 β€” Heat leaking from the house warms the attic and the roof deck above it, so snow melts on the upper roof. The water runs down to the overhang, which has no heat under it, and refreezes as a dam. An ice barrier membrane runs from the roof edge to at least 24 in inside the wall line, as a backup if water backs up under the shingles.

The Department of Energy’s Building America Solution Center says an ice dam needs three things: snow on the roof, a poorly air-sealed or poorly insulated attic, and freezing temperatures. It notes dams can form with as little as 2 in of snow on the roof.

University of Minnesota Extension describes the temperatures involved. The upper part of the roof surface sits above 32°F while the lower edge stays below it, averaged over days rather than hours, and the outside air has to be below freezing for the edge to stay cold. Snow melts on the warm upper roof, the water runs down, and it freezes again where the roof overhangs the wall and has no heat under it. Each thaw adds to the ridge, and the pool of water behind it grows.

Icicles are a warning sign. The DOE page says icicles often mean liquid water is building up behind the dam, where it can be drawn up under the shingles and cause leaks. A row of large icicles along an eave is worth a look in the attic and on the ceiling below.

Where the Heat Comes From

UMN Extension calls air leakage the major way heat reaches the roof in many homes. Warm indoor air rises through gaps in the top-floor ceiling and warms the underside of the roof deck. The common leak points and heat sources named by the DOE and UMN are:

Thin insulation adds to the problem by letting heat conduct straight through the ceiling, but a leaky ceiling with plenty of insulation can still cause ice dams because moving air carries heat past the insulation. UMN notes that sun alone causes the temperature difference only rarely.

The Permanent Fix, in Order

Both the DOE and UMN put the steps in the same order, and the order matters: insulation laid over an unsealed ceiling buries the leaks where they are hard to reach.

1
Air seal the ceiling. The DOE calls this the most important step. Seal every gap in the list above with foam, caulk or gaskets, weatherstrip the attic hatch, and box over recessed lights that are not rated for contact with insulation (or replace them with airtight, IC-rated fixtures). UMN suggests a blower door test with an infrared scan to find leaks you cannot see.
2
Insulate the attic floor. ENERGY STAR recommends R-49 in climate zones 2 and 3 and R-60 in zones 4 through 8, which covers most of the country where ice dams are common. If you can see the tops of the ceiling joists, you are well short of that. The attic insulation calculator gives the depth and bag count for your target, and what R-value do I need explains climate zones.
3
Ventilate the roof. Air should enter at the soffits, run up under the roof deck and leave at the ridge, keeping the deck cold. Install a baffle in every rafter bay at the eaves so insulation cannot block the soffit vents. The DOE recommends an air gap of at least 2 in under the deck; the IRC minimum is 1 in at the vent.

UMN adds a point that saves money: once the ceiling is sealed and insulated well, only a small amount of roof ventilation is needed, and it does not recommend powered attic fans for ice dams, which it says can cause attic moisture problems and unwanted negative pressure in the house. When you tighten a house, make sure fuel-burning appliances and exhaust fans still get the air they need to vent safely; a heating contractor can check this.

Work out attic insulation depth, bags and baffles

Attic Insulation Calculator β†’

Attic Ventilation Numbers

The International Residential Code sets the vent area for a vented attic as 1 sq ft of net free area for every 150 sq ft of attic floor. It allows 1 per 300 when 40 to 50% of the vent area is high on the roof, within 3 ft of the ridge, with the rest low, and the code’s other conditions are met, which include a vapor retarder on the warm side of the ceiling in the coldest zones. Net free area is printed on each vent, usually in square inches.

Attic FloorAt 1/150At 1/300High Vents at 1/300 (40–50%)
1,000 sq ft6.67 sq ft (960 sq in)3.33 sq ft (480 sq in)192–240 sq in
1,200 sq ft8 sq ft (1,152 sq in)4 sq ft (576 sq in)230–288 sq in
1,500 sq ft10 sq ft (1,440 sq in)5 sq ft (720 sq in)288–360 sq in
2,000 sq ft13.33 sq ft (1,920 sq in)6.67 sq ft (960 sq in)384–480 sq in

A 1,200 sq ft attic needs 8 sq ft (1,152 sq in) of net free area at 1/150, or 4 sq ft (576 sq in) at 1/300. Check what your local code adopts; ventilation rules vary by edition and by climate zone.

What to Do About an Ice Dam Right Now

If water is already coming in, the goal is to drain the water behind the dam and reduce the snow feeding it. None of these steps fixes the cause.

Expect more snow to stay on the roof after the fix. UMN notes that a well-insulated roof keeps its snow longer, and that a house built to current codes should carry it. If you are unsure about an older roof, check the plans or ask an engineer.

Heat Cable: A Stopgap, Not a Cure

Self-regulating heat cable laid in a zigzag along the eave, in the gutter and down the downspout keeps a path open for meltwater. It does not stop the melting that causes the dam. King Electric’s design guide says its cable is designed to remove ice, not accumulated snow, and will not keep snow from sliding off the roof.

It takes more cable than most people expect. King’s worked example, a 48 ft eave on a shingle roof with a 12 in overhang, 48 ft of gutter, one 22 ft downspout, two power connections and three splices, comes to 237.4 ft of cable, about five times the eave length (the heat cable calculator shows each line). Cable must be plugged into a ground-fault protected circuit and stay on the roof surface, never under the shingles.

Heat cable makes sense on a roof that keeps damming while you plan the attic work, or on a section that cannot be fixed from inside, such as the roof over a cathedral ceiling or a low porch roof.

Work out how much roof and gutter heat cable you need

Heat Cable Calculator β†’

Eave Membrane: The Backup Layer

A self-adhered ice barrier membrane under the shingles at the eaves seals around nails, so water backed up by a dam has a harder time getting through the roof deck. The DOE describes it as an added layer of protection should ice dams occur, not a way to prevent them. The IRC requires an ice barrier where ice has historically formed at the eaves, running from the roof edge to at least 24 in inside the exterior wall line.

Because that distance is measured to a point inside the wall, the membrane has to cover the overhang plus 24 in, measured up the slope. The overhang here is measured level, from the face of the wall out to the roof edge. Steeper roofs and deeper overhangs need more:

Eave Overhang4/12 Pitch6/12 Pitch8/12 Pitch12/12 Pitch
None25.3 in26.8 in28.8 in33.9 in
12 in37.9 in40.2 in43.3 in50.9 in
24 in50.6 in53.7 in57.7 in67.9 in

Membrane rolls are commonly 36 in wide, so a 12 in overhang on a 4/12 roof (37.9 in up the slope) already needs a second course or a wider roll. The membrane goes down when the roof is replaced; it is not something to add under existing shingles. The roofing calculator and the roof pitch calculator give the slope factor for your roof.

Ranked by value: seal the ceiling, insulate, ventilate, and use heat cable and membrane as protection while the attic work gets done or where it cannot be done.

Frequently Asked Questions

What causes ice dams?

Heat from the house melts snow on the upper roof, and the water refreezes at the cold eaves. The DOE says it takes snow on the roof, a poorly air-sealed or poorly insulated attic, and freezing temperatures. Air leaking through the top-floor ceiling is the main heat source in many homes.

How do I stop ice dams permanently?

In this order: air seal the ceiling, insulate the attic floor, then ventilate the roof from soffit to ridge with a baffle in every rafter bay. The DOE calls air sealing the most important step, and both the DOE and UMN Extension put it first.

Should I remove an ice dam myself?

Keep to what you can do from the ground. Rake snow off the lower roof gently with a roof rake, and on a warm day you can hose a channel through the dam, working up from the lower edge, so trapped water drains. Do not chip the ice or climb an icy roof; UMN recommends calling professionals for roof work in winter.

Does heat cable prevent ice dams?

It keeps a drainage path open through the dam, but it does not stop the melting that causes it. King Electric says its cable is designed to remove ice, not snow. Use it as a stopgap while you fix the attic, or on a section of roof the attic work cannot reach.

Do more attic vents stop ice dams?

Ventilation helps keep the roof deck cold, but it comes third. UMN Extension says that once the ceiling is sealed and insulated well, only a small amount of ventilation is needed, and it does not recommend powered attic fans for ice dams, which it says can cause attic moisture problems and unwanted negative pressure in the house.

How much attic ventilation do I need?

The IRC baseline is 1 sq ft of net free vent area per 150 sq ft of attic floor, or 1 per 300 when vents are split high and low and the code’s other conditions are met. A 1,200 sq ft attic needs 8 sq ft (1,152 sq in) at 1/150, or 4 sq ft at 1/300.

How much insulation stops ice dams?

ENERGY STAR recommends R-49 in zones 2 and 3 and R-60 in zones 4 through 8 for attics. Insulation only works with the air sealing done first, and it must not block the soffit vents, so install baffles at the eaves before blowing it in.

How far up the roof does ice and water shield go?

The IRC requires an ice barrier from the edge of the roof to at least 24 in inside the exterior wall line where ice has formed at the eaves. Measured up the slope, that is 37.9 in for a 12 in overhang on a 4/12 roof and 57.7 in for a 24 in overhang on an 8/12 roof, so most roofs need more than one 36 in course.

Are icicles a sign of an ice dam?

Often. The DOE says icicles are frequently a sign that liquid water is building up behind a dam, where it can be drawn under the shingles. Check the ceiling and the top of the exterior walls below a row of large icicles for stains or damp.

Can ice dams form on a roof with little snow?

Yes. The DOE notes ice dams can form with as little as 2 in of snow on the roof, as long as the upper roof is warm enough to melt it and the eaves stay below freezing.

Sources & Standards

Estimates for planning only. The figures here follow published model codes and industry standards, but those are adopted and amended locally, and older buildings are often legally exempt from the current edition. Check with your local code enforcement office or building department before you order or build β€” they are the authority that inspects the work, and what they require overrides anything on this page. See our full method and assumptions.

Last updated Β· How we calculate