On this page
What a Linear Foot Measures
A linear foot is 12 inches of length, nothing more. It ignores width and thickness, which is why it is the unit for anything sold by the run: baseboard and crown, fence rails, gutters, edging, countertop edges and most lumber at the yard. A 2x4 that is 8 ft long is 8 linear feet, and so is an 8 ft piece of 2x12.
Width and thickness come back in when you need an area or a volume. Square feet cover a surface, and board feet measure the wood itself. The table shows how they relate for common softwood sizes; the dressed size is what the board measures, and board feet use the nominal size.
| Nominal | Actual (dry) | Board Feet per Linear Foot | Linear Feet per 100 Board Feet |
|---|---|---|---|
| 1x4 | 3/4 × 3 1/2 in | 0.333 | 300 ft |
| 1x6 | 3/4 × 5 1/2 in | 0.5 | 200 ft |
| 1x8 | 3/4 × 7 1/4 in | 0.667 | 150 ft |
| 2x4 | 1 1/2 × 3 1/2 in | 0.667 | 150 ft |
| 2x6 | 1 1/2 × 5 1/2 in | 1 | 100 ft |
| 2x8 | 1 1/2 × 7 1/4 in | 1.333 | 75 ft |
| 2x10 | 1 1/2 × 9 1/4 in | 1.667 | 60 ft |
| 2x12 | 1 1/2 × 11 1/4 in | 2 | 50 ft |
Converting Square Feet to Linear Feet
To cover an area with boards, divide the area by the width each board covers. Working in inches:
Covered width is the face that shows once the board is installed. For square-edge boards that is the actual width (5 1/2 in for a nominal 6 in board). Shiplap, tongue-and-groove and lap siding cover less than their full width because of the overlap, so use the exposure or coverage the maker lists. For decking, add the gap between boards.
A 200 sq ft deck in 5 1/2 in boards with a 3/16 in gap: 200 × 12 ÷ 5.6875 = 422 linear feet. With 10% for waste that is 465 ft, or 59 boards at 8 ft. Linear feet per 100 sq ft for common widths:
| Covered Width | Tight (no gap) | With a 3/16 in Gap |
|---|---|---|
| 2.25 in | 533.3 ft | 492.3 ft |
| 3.25 in | 369.2 ft | 349.1 ft |
| 3.5 in | 342.9 ft | 325.4 ft |
| 5.5 in | 218.2 ft | 211 ft |
| 7.25 in | 165.5 ft | 161.3 ft |
| 9.25 in | 129.7 ft | 127.2 ft |
For decks, the deck board calculator also handles board direction and joist spacing. For walls, the wall paneling calculator and siding calculator deduct doors and windows.
Board Feet and Linear Feet
Hardwood and some framing lumber are priced by the board foot, a volume of 144 cubic inches. Board feet for a piece are:
Softwood is counted on its nominal size, so an 8 ft 2x6 is 2 × 6 × 8 ÷ 12 = 8 board feet even though it measures 1 1/2 by 5 1/2 in. Hardwood is usually sold rough and measured in quarters of an inch of thickness (4/4 is 1 in, 8/4 is 2 in), so use the rough thickness in the formula, not the planed one. The calculator’s board list covers nominal softwood sizes; for 5/4 or 8/4 hardwood, work it out with the formula above. To turn a board-foot price into a linear-foot price, multiply it by the board feet per linear foot from the table: at an example price of $3.00 a board foot, 1x8 is $2.00 a linear foot, because one linear foot of 1x8 is 0.667 board feet.
The lumber calculator totals board feet for a whole order.
Adding Up a Cut List
The cut-list option adds pieces that are already sized, in feet, inches and fractions, and gives the total run. It then plans the boards to buy: it places the longest pieces first, fits shorter ones into the offcuts with a saw kerf between them, and opens a new board only when nothing fits. With “the shortest length that fits each piece” it picks a stock length for each new board; pick one length if that is all your yard carries. It is a planning count, not an optimal cutting plan, so check it against your own layout before you buy.
- List the longest pieces first and give each its own board, then fill the offcuts with short pieces.
- Allow for the saw. Each cut removes the width of the blade: about 1/8 in for a full-kerf blade, less for a thin-kerf one. The feet and inches calculator splits a board into equal pieces with the kerf taken out.
- Buy long when it saves cuts. Two pieces just under 6 ft (5 ft 11 15/16 in, after one 1/8 in cut) come out of one 12 ft board; from 8 ft boards they take two, with about 2 ft wasted on each.
- Check that the frame is square before you cut the last pieces. The squaring calculator gives the diagonals.
Mistakes That Throw Off a Linear-Foot Order
- Using the nominal width for coverage. A 1x6 covers 5 1/2 in, not 6 in. Using 6 in under-orders by about 8%.
- Leaving out the gap or the overlap. Deck gaps add coverage; shiplap overlaps take it away.
- Comparing a per-piece price with a per-foot price. An 8 ft board priced at $9.98 (an example price) is $1.25 a linear foot. Convert before you compare stores.
- Forgetting waste. Offcuts, splits and a bad board or two are normal. 10% is a starting point; diagonal layouts need more.
- Mixing decimal feet with feet and inches. 10.5 ft is 10 ft 6 in, not 10 ft 5 in.
For trim around a room, the trim and baseboard calculator measures the perimeter and deducts doors.
Frequently Asked Questions
How do I calculate linear feet?
Add up the lengths, ignoring width and thickness. For a cut list, multiply each length by how many pieces you need and add the results: 14 boards at 8 ft plus 4 boards at 12 ft is 112 + 48 = 160 linear feet. Convert inches to feet first by dividing by 12, so 10 ft 6 in is 10.5 ft.
How do I convert square feet to linear feet?
Multiply the square feet by 12 and divide by the width each board covers in inches, plus any gap. 200 sq ft of 5 1/2 in deck boards with a 3/16 in gap is 200 × 12 ÷ 5.6875 = 422 linear feet before waste, or about 465 ft with 10% extra.
How many linear feet are in a square foot?
It depends on the board width: 12 ÷ width in inches. A 5 1/2 in board needs 2.18 linear feet per square foot, a 3 1/2 in board 3.43 ft, and a 7 1/4 in board 1.66 ft. A square foot and a linear foot measure different things, so there is no single conversion.
What is the difference between a linear foot and a board foot?
A linear foot is 12 in of length of any board. A board foot is a volume: 144 cubic inches, such as a board 1 in thick, 12 in wide and 12 in long, counted on the nominal size. One linear foot of 1x12 or 2x6 is 1 board foot; one linear foot of 2x4 is 0.667 board feet.
How do I convert board feet to linear feet?
Multiply the board feet by 12 and divide by the nominal thickness times the nominal width. 100 board feet of 1x8 is 100 × 12 ÷ 8 = 150 linear feet, which is 19 boards at 8 ft.
Is a linear foot the same as a foot?
Yes. “Linear” only makes clear that the price or quantity is for length alone, whatever the width. Trim, fencing, gutters, countertop edges and lumber are all sold this way.
How do I convert linear feet to meters?
Multiply by 0.3048, the exact length of a foot in meters. 160 linear feet is 48.77 m. To go the other way, divide meters by 0.3048, or multiply by 3.281.
How many linear feet are in a linear yard?
3. Fabric, carpet runners and some fencing are sold by the linear yard; divide linear feet by 3 to compare. 160 linear feet is 53.33 linear yards.
How many 8 ft boards make 465 linear feet?
465 ÷ 8 = 58.1, so buy 59 boards. Always round the board count up. The calculator does this from the square feet and the stock length you pick, and the waste allowance is already in the 465.
Why does my cut list need more boards than the total suggests?
Because pieces have to come out of whole boards. Three 5 ft pieces add up to 15 linear feet, but they cannot be cut from two 8 ft boards; they take three, with 3 ft left on each. Group the pieces so they fit your stock lengths, cut the longest first, and allow about 1/8 in for each saw cut.
Sources & Standards
- American Lumber Standard Committee — Softwood lumber nominal vs. dressed dimensions
- NIST Guide to the SI (SP 811), Appendix B.9 — Length: inch = 0.0254 m and foot = 0.3048 m, both exact
Estimates for planning only. Quantities are calculated from standard coverage and yield figures, with a waste allowance where the page states one. Always confirm against the manufacturer figures on the product you buy, and check local requirements before ordering. Dollar figures on this page are typical US planning ranges, not quotes: prices vary by region, supplier and season, so check current local prices before you budget. See our full method and assumptions.