Hanging wallpaper instead?
Try our Wallpaper Calculator →Installing new drywall first?
Calculate Drywall Sheets Needed →How to Calculate Paint for a Room
Measure the wall area (the room's perimeter times its ceiling height), take off about 21 sq ft for each door and 15 for each window, multiply by the number of coats, and divide by 350 to 400 sq ft per gallon. A 12 × 12 ft room with 8 ft walls, one door and one window needs 2 gallons for two coats.
Basic Formula
Step by Step
- Calculate wall area: Perimeter (2 × length + 2 × width) × wall height
- Add ceiling if painting it: Length × width
- Subtract openings: Doors (~21 sq ft each), windows (~15 sq ft each)
- Multiply by coats: Most color changes need 2 coats
- Divide by coverage: Typically 300–400 sq ft per gallon depending on finish
Coverage and Sheen
Sheen moves coverage by 50 to 100 sq ft per gallon across the range below. Its bigger effect is on cleaning and on how much the wall shows its flaws. The higher the sheen, the more washable the paint and the more mercilessly it shows every dent, patch and roller mark underneath.
| Finish | Coverage | Washability | Hides Flaws | Where It Belongs |
|---|---|---|---|---|
| Flat / matte | ~400 sq ft/gal | Lowest | Best | Ceilings, low-traffic walls |
| Eggshell | ~350 sq ft/gal | Moderate | Good | Bedrooms, living rooms |
| Satin | ~350 sq ft/gal | Good | Fair | Kitchens, bathrooms, hallways |
| Semi-gloss | ~350 sq ft/gal | High | Poor | Trim, doors, cabinets |
| Gloss | ~300 sq ft/gal | Highest | Worst | Front doors, accent millwork |
Sheen names are not standardized between manufacturers — one brand's eggshell can be another's satin. Compare the gloss level on the can, not the word on the label. Our paint sheen guide covers the full ladder, room by room, including how sheen behaves on touch-ups and under raking light.
Painting outside? Exterior coverage works differently — stucco and rough-sawn cedar can take roughly double the paint of smooth siding. Use the exterior paint calculator, which adjusts the spread rate by substrate. For what the job costs, see how much it costs to paint a room.
On this page
Do I Need Primer?
Primer isn't always necessary, but it helps in several situations:
- New drywall: Always prime bare drywall to seal the surface
- Dark to light color change: A tinted primer reduces the number of top coats needed
- Stains or odors: Use a stain-blocking primer for water stains, smoke, or pet odors
- Glossy surfaces: Primer helps paint adhere to slick finishes
If you're painting a similar color over a previously painted wall in good condition, you can usually skip primer and go straight to two coats of paint. When you do need it, set Primer in the calculator to spot-priming or a full coat and it adds a separate primer line; the paint gallons do not change.
Which primer matters as much as whether you use one. Water-based, oil and shellac primers block very different things — a water stain painted over with the wrong primer will bleed back through however many coats you apply. Our primer and stain-blocking guide covers what each family seals.
How Much Paint for a Room?
Wall area is the perimeter times the ceiling height. These are the common room sizes worked out for you, assuming 8 ft ceilings, two coats at 350 sq ft per gallon (the calculator's rate for eggshell and satin), and one door plus one window deducted. Flat paint, at 400 sq ft per gallon, comes out about an eighth lower.
| Room Size | Wall Area | Paintable (less openings) | Gallons (2 coats) | Buy |
|---|---|---|---|---|
| 8 × 10 ft | 288 sq ft | 252 sq ft | 1.4 | 2 gallons |
| 10 × 12 ft | 352 sq ft | 316 sq ft | 1.8 | 2 gallons |
| 12 × 12 ft | 384 sq ft | 348 sq ft | 2.0 | 2 gallons |
| 12 × 16 ft | 448 sq ft | 412 sq ft | 2.4 | 3 gallons |
| 14 × 20 ft | 544 sq ft | 508 sq ft | 2.9 | 3 gallons |
| 20 × 20 ft (two-car garage) | 640 sq ft | 604 sq ft | 3.5 | 4 gallons (or a 5-gal pail) |
A 5-gallon pail costs less than four separate gallons and removes any risk of color variation between cans. If you're at three gallons or more, price the pail.
If you're buying separate gallons of the same color, box them — pour all the cans into one bucket and mix before you start. Tinted paint varies slightly between cans, and boxing guarantees the last wall matches the first.
Painting a Garage
The 20 × 20 row assumes 8 ft walls and house-sized openings. Garages often have 9 ft walls and a big overhead door instead of a window, so work it out by hand and use the Total Square Feet tab, because Room mode only deducts standard doors and windows.
A 20 × 20 ft two-car garage with 9 ft walls has 80 × 9 = 720 sq ft of wall. Take off 112 sq ft for a 16 × 7 ft overhead door and 21 sq ft for the door into the house, and 587 sq ft is left. Two coats at 350 sq ft per gallon is 3.35 gallons, so buy 4 gallons or a 5-gallon pail. Measure your own overhead door; single-car doors are often 8 or 9 ft wide.
Bare, taped drywall is common in garages and soaks up the first coat. Prime it first (see Do I Need Primer?), then count your two finish coats on top.
Ceilings, Trim, and Doors
- Ceiling: length × width. A 12 × 12 room is 144 sq ft — under half a gallon per coat. See the ceiling paint calculator.
- Trim and baseboards: roughly 1 quart per 100 linear feet, per coat.
- Doors: about 1 quart per 3 doors, per coat, painting both faces.
- Window casings: roughly 1 quart per 8–10 windows, per coat.
How Much Paint for One Wall or an Accent Wall?
One wall is the easiest case in the whole job: width × height, minus any window or door on that wall. The arithmetic is easy. The usual mistake is buying a gallon, because a single accent wall rarely needs one. Switch the calculator above to One Wall and it sizes the purchase in quarts where quarts are enough.
| Wall Width | Area (8 ft ceiling) | Buy | Area (9 ft ceiling) | Buy |
|---|---|---|---|---|
| 8 ft | 64 sq ft | 2 quarts | 72 sq ft | 2 quarts |
| 10 ft | 80 sq ft | 2 quarts | 90 sq ft | 3 quarts |
| 12 ft | 96 sq ft | 3 quarts | 108 sq ft | 3 quarts |
| 14 ft | 112 sq ft | 3 quarts | 126 sq ft | 3 quarts |
| 16 ft | 128 sq ft | 3 quarts | 144 sq ft | 1 gallon |
| 20 ft | 160 sq ft | 1 gallon | 180 sq ft | 1 gallon + 1 quart |
Two coats at 350 sq ft per gallon, no openings deducted.
Two coats, no openings deducted. Deduct 15 sq ft for a window or 21 for a door if one lands on your wall.
Where quarts stop making sense
A quart is a quarter of a gallon but costs far more than a quarter of the price, so the table crosses over twice. Once you need four quarts, buy the gallon — same paint, less money, and you keep a sealed remainder for touch-ups. And when you land just over a gallon, as the 20 × 9 ft wall does at 1.03 gallons, a gallon plus a quart is usually cheaper than two gallons. We round up to whole units because running out mid-wall means a visible lap mark, but the unit is yours to choose.
Accent walls are usually the deep, saturated color in the room, and deep colors are exactly the ones that need a third coat over a tinted primer. Check the three-coat question in the FAQ below before you size the can — a third coat is 50% more paint, which can move you up a tier.
When you already know the square footage
If you have measured the surface yourself, added up several rooms, or are painting something that is not a rectangle at all, use the Total Square Feet tab and enter the area directly. Openings are not subtracted in that mode — the figure you type is taken as the surface being covered, so take the windows and doors off before you enter it. Enter wall area, not the floor area of the room or house; the next section shows why the two are far apart.
How Much Paint per Square Foot?
Each square foot of wall takes about 1/350 of a gallon per coat, which is roughly a third of a fluid ounce. For two coats, divide the paintable square feet by 175 to get gallons. Flat paint goes a little further (1/400 of a gallon) and gloss a little less (1/300).
| Paintable Area | 1 Coat | 2 Coats | Buy (2 coats) |
|---|---|---|---|
| 100 sq ft | 0.29 gal | 0.57 gal | 3 quarts |
| 250 sq ft | 0.71 gal | 1.43 gal | 2 gallons |
| 500 sq ft | 1.43 gal | 2.86 gal | 3 gallons |
| 1,000 sq ft | 2.86 gal | 5.71 gal | 6 gallons |
| 1,500 sq ft | 4.29 gal | 8.57 gal | 9 gallons |
| 2,000 sq ft | 5.71 gal | 11.43 gal | 12 gallons |
Figures use 350 sq ft per gallon (eggshell, satin or semi-gloss). The Buy column is what the calculator's Total Square Feet tab gives at two coats. At three gallons or more, a 5-gallon pail is usually cheaper than the same paint in single gallons.
Floor Area Is Not Wall Area
The easiest way to get this badly wrong is to use the floor area. A house listed at 1,500 sq ft has 1,500 sq ft of floor, and its walls are a different number entirely. Using the rooms in the table above, an 8 × 10 ft room has 80 sq ft of floor and 252 sq ft of paintable wall (about 3 times as much). A 12 × 12 ft room has 144 and 348 (2.4 times). A 20 × 20 ft room has 400 and 604 (1.5 times). Small rooms have far more wall per square foot of floor, so no single multiplier works for a whole house.
If you are pricing a whole interior, run each room through the Whole Room tab and add the gallons, or add up the wall areas and enter the total in Total Square Feet. For a ceiling, floor area is the right number; see the ceiling paint calculator.
How Much Does a Pint, Quart, Gallon or 5-Gallon Bucket of Paint Cover?
A gallon of interior wall paint covers 350 to 400 sq ft in one coat. That makes a quart about 90 to 100 sq ft, a pint about 45 to 50, and a 5-gallon bucket 1,750 to 2,000. Two coats halve every figure, so a gallon does about 175 to 200 sq ft of finished, two-coat wall.
| Container | 1 Coat, Flat (400/gal) | 1 Coat, Eggshell or Satin (350/gal) | 2 Coats, Eggshell or Satin |
|---|---|---|---|
| Pint (1/8 gal) | 50 sq ft | 44 sq ft | 22 sq ft |
| Quart (1/4 gal) | 100 sq ft | 88 sq ft | 44 sq ft |
| Gallon | 400 sq ft | 350 sq ft | 175 sq ft |
| 5-gallon bucket | 2,000 sq ft | 1,750 sq ft | 875 sq ft |
Gloss is the exception at about 300 sq ft per gallon, so a quart of gloss covers about 75 sq ft and a 5-gallon bucket about 1,500. These are the calculator's planning rates. The spread rate printed on your can overrides them, and primers, ceiling paints and exterior coatings publish their own.
A pint is a sample size: enough for test patches on two or three walls, or a small piece of furniture, but not a whole wall. For one wall, the One Wall tab sizes the purchase in quarts when three quarts or fewer will do, and in gallons above that. The real coverage you get also depends on texture, porosity and how big a color change you are making; see What Changes Your Coverage.
What Changes Your Coverage
The 350–400 sq ft on the can assumes a smooth, primed, similarly-colored wall. Real walls rarely are, and these factors matter more than the brand you buy:
| Factor | Effect on Coverage |
|---|---|
| Smooth drywall | Full rated coverage |
| Light orange-peel texture | Reduce by 10–15% |
| Heavy knockdown texture | Reduce by 20–30% |
| Bare drywall (unprimed) | Reduce by 20%+ — prime instead |
| Raw or patched plaster | Reduce by 20–30% |
| Spraying instead of rolling | Reduce by 20–40% from overspray |
| Dark color over light | Often a third coat |
Deep reds, bright yellows, and strong oranges are the hardest colors to cover, because their pigments are naturally less opaque. Expect three coats over anything but a matched tinted primer — and have the primer tinted toward the final color, which usually saves a full coat.
Frequently Asked Questions
How much does a gallon of paint cover?
One gallon covers approximately 350–400 square feet on a smooth surface with one coat. Rough or textured surfaces may require more paint per coat. If your can prints a different spread rate, choose Custom in Paint Finish and type it in.
How many coats of paint do I need?
Two coats is standard for most projects. You may get away with one coat if you're painting the same color. Dramatic color changes (especially dark to light) may need three coats or a coat of primer first.
How much paint for a 12×12 room?
A 12 × 12 ft room with 8 ft ceilings has 384 sq ft of wall. Take off one door and one window and 348 sq ft is left. Two coats at 350 sq ft per gallon is 2.0 gallons, so buy 2. Painting the ceiling too adds 144 sq ft per coat.
Should I buy extra paint?
The calculator already rounds up to the next whole gallon or quart, and what is left over is your touch-up paint. When the exact figure lands right on a whole can, as a 12 × 12 room does at 2.0 gallons, add a quart. Sealed and kept somewhere cool and dry, leftover paint lasts for years.
How do I calculate paintable wall area?
Multiply the room's perimeter by the ceiling height, then subtract openings — about 21 sq ft per door and 15 sq ft per window. A 12 × 12 ft room with 8 ft ceilings has 384 sq ft of wall, or about 348 sq ft paintable after one door and one window.
How much does a 5-gallon bucket of paint cover?
About 1,750 to 2,000 sq ft in one coat, or 875 to 1,000 sq ft at two coats. It is usually cheaper than five single gallons and has no color variation between cans, so price the pail once you need three gallons or more.
What is boxing paint, and when do I need to?
Pouring several cans of the same color into one bucket and stirring them together before you start. Tinted paint varies slightly from can to can, and boxing makes the wall you paint last match the one you painted first. You need it whenever you buy separate gallons; a 5-gallon pail is already one batch.
How much does a quart of paint cover?
About 90 to 100 sq ft in one coat, or 45 to 50 sq ft at two coats. That is enough for a small accent wall or a door, but once you need four quarts, a gallon is cheaper.
Does texture change how much paint I need?
Considerably. Light orange-peel texture cuts coverage by 10–15%, and heavy knockdown by 20–30%. Spraying instead of rolling costs another 20–40% to overspray. The number on the can assumes smooth, primed drywall.
Which colors need three coats?
Deep reds, bright yellows, and strong oranges — their pigments are inherently less opaque. Have your primer tinted toward the final color and you'll usually save a coat.
How long should I wait between coats?
Check the can, but typically two to four hours for latex. Recoating too early lifts the first coat and leaves streaks you can't paint out. Full cure — when the paint reaches its final hardness and washability — takes up to 30 days.
What order should I paint a room in?
Ceiling, then walls, then trim. Spatter falls downward, so the ceiling has to come first, and it's much easier to cut a clean line on trim against a finished wall than the other way round. Wait the recoat time on the can, usually two to four hours for latex, before the second coat. The full method, from cutting in to keeping a wet edge, is in How to Paint a Room.
How much paint do I need for a door or trim?
A quart covers about 3 doors per coat, painting both faces, so one door at two coats takes about two-thirds of a quart. Buy a quart. For trim, allow roughly 1 quart per 100 linear feet per coat, and for window casings about 1 quart per 8–10 windows.
How much paint do I need for one wall?
Multiply the wall width by its height and take off 15 sq ft for a window or 21 for a door. A 14 × 8 ft wall is 112 sq ft, which at two coats is 3 quarts — not the gallon most people buy. Use the One Wall tab above. Once the answer reaches four quarts, buy a gallon instead; it is the same paint for less money.
Does paint sheen change how much paint I need?
Yes, and this calculator accounts for it. It assumes 400 sq ft per gallon for flat or matte, 350 for eggshell, satin and semi-gloss, and 300 for gloss — a glossier film has to go on more evenly to look right, so it stretches less far. Flat hides better per coat but marks more easily. These are planning figures; the spread rate printed on your particular can overrides them.
Sources & Standards
- KILZ 2 All-Purpose primer product page — Coverage 300-400 sq ft per gallon depending on application method and surface porosity
Estimates for planning only. Quantities are calculated from standard coverage and yield figures, with a waste allowance where the page states one. Always confirm against the manufacturer figures on the product you buy, and check local requirements before ordering. See our full method and assumptions.