📐 Area to Sheathe
ft
For a wall, the run of the wall. For a roof, the length along the ridge.
ft
Wall height, or rafter length up the slope — not the footprint.
Nearly everything is 4 × 8. Longer panels exist for tall walls.
Sheathing waste is offcuts at openings, hips and valleys.
sq ft
Total area of windows and doors, if you are deducting them. Leave at 0 to sheathe over and cut out after.
✓ Results
Area to Cover 400 sq ft
Sheets for Exact Coverage 13
14 sheets
Sheets to Buy (with waste)
Coverage Purchased 448 sq ft
Panel Edge Gap to Leave 1/8 in at every edge and end

Sheathing a roof? Start from the sloped area, not the footprint.

Work out roof area first →

On this page

  1. How to Calculate Sheathing Sheets
  2. Sheet Sizes and Coverage
  3. Reading the Span Rating
  4. Gapping, and Other Ways to Get It Wrong
  5. Frequently Asked Questions

How to Calculate Sheathing Sheets

Sheet goods are the simplest estimate on a build: an area divided by the area of one sheet. What trips people up is which area to use and how much to add on top.

  1. Work out the surface area. For a wall that is length × height. For a roof it is the sloped area, which is bigger than the footprint — take it from the roofing calculator rather than measuring the plan.
  2. Divide by the sheet coverage. A 4 × 8 covers 32 sq ft.
  3. Round up. Half a sheet is not a purchasable unit, and the half you need is rarely the shape you have left.
  4. Add waste. 10% on a plain rectangle, 15% on anything with hips, valleys or a lot of openings.
  5. Decide about openings. On a wall, most framers sheathe straight over them and cut out afterwards. Deduct only for something large, like a garage door.

A 40 × 10 ft wall is 400 sq ft, which is 12.5 sheets — call it 13 for exact coverage, and 14 sheets once the allowance goes on.

Sheet Sizes and Coverage

How far each panel size goes, and how many it takes to cover some common areas. Every figure is this calculator's own output at 0% waste:

Sheet SizeCovers100 sq ft200 sq ft400 sq ft1,000 sq ft
4 ft × 8 ft32 sq ft471332
4 ft × 9 ft36 sq ft361228
4 ft × 10 ft40 sq ft351025

The longer panels are not usually about coverage — they are about avoiding a horizontal joint on a 9 or 10 ft wall. A joint partway up a wall has to land on blocking, so a single tall panel saves both the blocking and the fussing.

Reading the Span Rating

The one question this calculator deliberately does not answer is how thick your sheathing should be. That is structural, it depends on how far apart your framing is, and the panel itself already carries the answer.

Look for two numbers separated by a slash on the panel stamp, such as 32/16:

Common ratings run 24/0, 24/16, 32/16, 40/20 and 48/24. Match the rating to your actual framing spacing and to what your local code requires; where the two disagree, the code wins. The same goes for the nailing schedule, which changes for braced wall panels and in high-wind and seismic regions.

Run the panels with the long dimension across the supports. That is the orientation the span rating assumes, because the strength axis runs the long way. Turn a panel the other way and the rated span no longer applies.

Gapping, and Other Ways to Get It Wrong

Frequently Asked Questions

How many sheets of plywood do I need?

Divide the area by the coverage of one sheet and round up. A 4 × 8 sheet covers 32 sq ft, so a 400 sq ft wall needs 400 ÷ 32 = 12.5, rounded to 13 sheets for exact coverage — and 14 once you add the usual 10% for offcuts. You cannot buy half a sheet, and the half you would need is rarely the shape that is left over.

How many square feet is a sheet of plywood?

A standard 4 ft × 8 ft sheet is 32 sq ft. A 4 × 9 is 36 sq ft and a 4 × 10 is 40 sq ft. Those longer panels exist mainly for 9 and 10 ft walls, where they let you sheathe full height without a horizontal joint.

What thickness of sheathing do I need?

That is set by how far apart your supports are, and it is answered by the span rating stamped on the panel, not by a rule of thumb. The stamp shows two numbers separated by a slash — something like 32/16. The left number is the maximum support spacing in inches when the panel is used as roof sheathing; the right is the maximum when it is used as a subfloor. Match the rating to your framing and to what your local code requires.

What do the two numbers on a plywood stamp mean?

They are the span rating. On a panel marked 32/16, it may span supports up to 32 in apart as roof sheathing, or up to 16 in apart as subfloor. Common ratings include 24/0, 24/16, 32/16, 40/20 and 48/24. A zero on the right means the panel is not rated for use as a subfloor at all.

Should I leave a gap between sheets?

Yes. Panels take on moisture and grow, and a wall sheathed tight will buckle at the joints. The standard recommendation is 1/8 in at all panel edges and ends — roughly the thickness of an 8d nail shank, which is the traditional way of setting it. Some panels are made with a slight edge profile that builds the gap in; those say so on the stamp.

Plywood or OSB for sheathing?

Structurally they are interchangeable at the same span rating — both are covered by the same performance standards and both carry the same stamp. The practical differences are that OSB is usually cheaper and comes in longer lengths, while plywood dries out faster after it gets wet and holds a fastener slightly better at the edge. For most walls and roofs the choice is price and availability.

Should I deduct window and door openings?

Usually not, on a wall. Most framers sheathe straight over the openings and cut them out afterwards, because it is faster, keeps the panel joints on the layout, and the cut-outs strengthen nothing if they are left as seams. Deduct only if the openings are large enough to change the sheet count meaningfully — a garage door, say. This calculator lets you enter a deduction if you want one.

How do I calculate roof sheathing?

Use the sloped area, not the footprint. A roof surface is always larger than the plan area beneath it, and the difference is the slope factor for your pitch. Work the roof area out first with our roofing calculator, then bring that figure here as the area to cover.

Which way do sheathing panels run?

On floors and roofs, with the long dimension across the supports, which is how the span rating is established in the first place — the strength axis runs the long way, and turning a panel the other way there means the rated span no longer applies. Walls are the exception: panels can run horizontally or vertically over studs, and vertical is common where the panel is doing the bracing and you want it to tie the plates together.

How many sheets for a 1,000 square foot roof?

1,000 ÷ 32 = 31.25, so 32 sheets for exact coverage and 35 with a 10% allowance. Go to 15% if the roof has hips, valleys or dormers, because every one of those produces angled offcuts that fit nowhere else.

How much waste should I allow for sheathing?

10% on a plain rectangular wall or a simple gable roof, and 15% where there are hips, valleys, dormers or a lot of openings. Sheathing waste is nearly all offcuts — the strip left when a panel runs past a corner, or the wedge cut off at a valley — so it scales with how cut-up the surface is, not with its size.

How are sheathing panels fastened?

Nailed to every support they cross, with a closer spacing around the panel edges than in the field. The exact schedule — nail size, edge spacing and field spacing — is a code table, and it changes for braced wall panels and in high-wind and seismic areas. Take it from the fastening schedule in your local code rather than from a material calculator.

Sources & Standards

Estimates for planning only. This calculator sizes material quantities. It does not size structural members, verify load paths, or confirm compliance with the code in your jurisdiction. Local requirements — frost depth, footing sizes, permits, and inspections — override anything here. Check with your local code enforcement office or building department before you build. They are the authority that inspects and signs off the work, they amend the model codes, and what they say overrides any figure on this page. For structural or safety-critical work, have the design checked by a licensed engineer or contractor as well. See our full method and assumptions.

Last updated · How we calculate