📐 Wall Area
ft
Add up the runs of every wall you are siding — the perimeter, for a whole house.
ft
Average height. Add for gable ends below.
sq ft
Gable triangles are half the base times the height. Add them here.
sq ft
Windows and doors. Most installers deduct only the large ones — see below.
Vinyl comes by the square; lap siding comes by the plank at a set exposure.
in
How much of each plank shows once the next one laps it. Printed on the carton.
ft
Most fiber cement lap is 12 ft.
%
10% on a plain rectangle; 15% with lots of gables, corners and openings.
✓ Results
Gross Wall Area 1,080 sq ft
Net Area to Cover 1,080 sq ft
12 squares
Siding to Buy
Boxes or Pieces 6 boxes (about 2 squares each)
Coverage Purchased 1,200 sq ft
Starter Strip 120 linear ft

Painting the siding rather than replacing it?

Use the exterior paint calculator →

On this page

  1. How to Measure a House for Siding
  2. How Siding Is Sold
  3. Siding for Common House Sizes
  4. The Trim Is Half the Job
  5. Frequently Asked Questions

How to Measure a House for Siding

Siding is an area estimate with two things people leave out: the gables, and the fact that lap siding covers less than its width.

  1. Add up the wall runs. For a whole house that is the perimeter. Do not measure each elevation separately unless the heights differ.
  2. Multiply by the wall height to get the rectangular part.
  3. Add each gable. A gable is a triangle — half the base times the height to the ridge. A 30 ft gable rising 8 ft is 120 sq ft, and a house with two of them is more than two squares of siding in triangles alone.
  4. Deduct the large openings only. Take off a garage door or a picture window; leave the small ones in. The offcuts around a bathroom window almost never reach another wall.
  5. Add waste — 10% plain, 15% cut-up.

A house with 120 linear ft of wall at 9 ft is 1,080 sq ft, which at 10% comes to 12 squares of vinyl, or 170 planks of 12 ft lap at a 7 in exposure.

How Siding Is Sold

The two materials are counted differently, which is the main thing to get straight before you call a supplier:

ProductSold ByTypical Packing / ExposureCoverage
Vinyl, double 4 inthe square (100 sq ft)~2 squares per boxarea ÷ 100
Vinyl, double 5 inthe square (100 sq ft)~2 squares per boxarea ÷ 100
Fiber cement lap, 8-1/4 inthe plank7 in exposure, 12 ft7.0 sq ft per plank
Fiber cement lap, 7-1/4 inthe plank6 in exposure, 12 ft6.0 sq ft per plank
Fiber cement lap, 12 inthe plank10-3/4 in exposure, 12 ft10.75 sq ft per plank

Exposure is the figure that matters for lap siding, and it is not the plank width. An 8-1/4 in plank laps 1-1/4 in under the one above it, so only 7 in shows — and 7 in is what covers your wall. A 12 ft plank therefore covers 7 sq ft, not the 8.25 sq ft its width implies. Getting this wrong under-orders by around 15%.

Exposure varies by product and manufacturer and is printed on the carton. The calculator takes it as an input for that reason; the figures above are common values, not a specification.

Siding for Common House Sizes

Walls only — no gables, no deductions, at 10% waste and a 7 in exposure for the plank column. Every figure is this calculator's own output:

HousePerimeterWall HeightGross AreaVinylLap Planks
24 × 40 ft, 1 story128 ft9 ft1,152 sq ft13 squares182 planks
28 × 48 ft, 1 story152 ft9 ft1,368 sq ft16 squares215 planks
24 × 40 ft, 2 story128 ft18 ft2,304 sq ft26 squares363 planks
32 × 56 ft, 2 story176 ft18 ft3,168 sq ft35 squares498 planks

Add your gables to these. A pair of 30 ft gables at 8 ft of rise is another 240 sq ft, which is three more squares once waste goes on.

The Trim Is Half the Job

Panels are the easy part of a siding order. The pieces that take the time are the trim, and they are counted in linear feet rather than area:

These depend on your elevation rather than your area, which is why the calculator sizes the starter strip and leaves the rest to a count off the drawing.

One fastening note that is not optional. Vinyl hangs; it is not pinned. Nails go in the center of the slot and are left a little loose, because a 12 ft panel expands and contracts noticeably with temperature and a panel nailed tight will buckle in the first hot spell. Fastening schedules also tighten in high-wind regions, so follow the manufacturer instructions and confirm with your local code enforcement office.

Frequently Asked Questions

How much siding do I need?

Work out the wall area, add the gable triangles, take off the large openings, then add waste. A house with 120 linear ft of wall at 9 ft is 1,080 sq ft; at 10% waste that is 1,188 sq ft, or 12 squares of vinyl. A square is 100 sq ft, and vinyl is usually boxed two squares to a carton, so that is 6 boxes.

What is a square of siding?

100 square feet. It is the unit siding and roofing are both sold and quoted in, and it exists because it makes a house-sized number small enough to talk about — "eighteen squares" rather than "eighteen hundred square feet". Vinyl is typically packed two squares to a box.

What does exposure mean on lap siding?

The part of each plank you can still see after the next plank laps over it. A 8-1/4 in plank with a 1-1/4 in overlap has a 7 in exposure, so each 12 ft plank covers 7 in × 12 ft = 7 sq ft — not the 8.25 sq ft its width suggests. Exposure varies by product and it is printed on the carton; enter yours rather than assuming.

Should I deduct windows and doors from siding?

Deduct the large ones and leave the rest in as waste allowance. A garage door or a picture window is worth taking off; a bathroom window is not, because the offcuts around it rarely reach another wall. Many installers deduct nothing under about 10 sq ft and treat it as part of the waste factor, which is roughly what it works out to.

How do I calculate a gable?

A gable is a triangle: half the base times the height. A 30 ft wide gable rising 8 ft to the ridge is 30 × 8 ÷ 2 = 120 sq ft. Do each gable separately and add them in — they are the part of a siding estimate people forget, and on a two-gable house they can add two squares or more on their own.

How many boxes of vinyl siding are in a square?

A square is 100 sq ft and vinyl is most often boxed two squares to a carton, so one box covers about 200 sq ft. Cartons vary by profile and manufacturer though — a double 4 in and a double 5 in do not pack the same — so check the coverage printed on the box before you count pallets.

How much waste should I allow for siding?

10% on a plain rectangular house, 15% where there are gables, dormers, bay windows or a lot of corners. Siding waste is almost entirely offcuts — the end of a run that is too short to start the next one — so it scales with how cut-up the elevation is rather than how big it is.

What trim do I need with siding?

Beyond the panels: starter strip along the bottom of every wall, J-channel around every window, door and roofline, outside and inside corner posts, and utility trim at the top. The starter strip runs the full perimeter, which this calculator gives you; count the corners and measure around the openings for the rest, because they depend on your elevation rather than your area.

Vinyl or fiber cement?

Vinyl is cheaper, lighter, and goes up faster; it never needs painting but it also cannot be painted convincingly, and it can warp near a reflective window. Fiber cement holds paint, resists impact far better and is what most design guidelines call for — but it is heavy, needs specific cutting gear and dust control, and costs considerably more installed. Both are ordered off the same wall area.

How many planks of fiber cement do I need?

Divide the net area by the coverage of one plank, which is exposure × length. At a 7 in exposure a 12 ft plank covers 7 sq ft, so 1,080 sq ft plus 10% waste needs 170 planks. Order by the piece and expect the yard to quote you in pieces, not squares.

Does siding need to be nailed a certain way?

Yes, and it matters more than people expect. Vinyl must hang loose — nailed in the center of the slot, not driven tight — because a 12 ft panel moves noticeably with temperature and pinning it causes buckling. Fastening schedules also tighten in high-wind areas. Follow the manufacturer instructions, and check with your local code enforcement office, which is the authority that inspects it.

Do I need house wrap under siding?

A water-resistive barrier behind the cladding is normally required, and how it is detailed — laps, flashing, drainage at the bottom — is what keeps water out of the wall. It is a code matter that varies by jurisdiction and by climate zone, so confirm the requirement with your local building department before you start, not after the panels are up.

Sources & Standards

Estimates for planning only. The figures here follow published model codes and industry standards, but those are adopted and amended locally, and older buildings are often legally exempt from the current edition. Check with your local code enforcement office or building department before you order or build — they are the authority that inspects the work, and what they require overrides anything on this page. See our full method and assumptions.

Last updated · How we calculate