Need the mortar that goes with it?
Use the mortar calculator →On this page
Flats and Corners Are Two Different Orders
Manufactured stone veneer is the one cladding sold in two units at once, and getting that wrong is an easy way to make a veneer order expensive.
- Flats are the field stone that covers the wall face. Sold by the square foot, usually 10 sq ft to a box.
- Corners are L-shaped pieces with two finished faces, used so an outside corner never shows a cut edge. Sold by the linear foot, usually 6 to 8 ft to a box, and considerably more expensive per piece.
The deduction is the thing. A corner piece wraps the corner and covers part of both walls, so every linear foot of corner takes up roughly half a square foot of the flat area you measured. Order the full wall area in flats and the corners on top, as most people do, and you have paid twice for that strip.
On a 20 × 8 ft wall with two 8 ft corners: 160 sq ft gross, less 8 sq ft covered by the 16 linear ft of corner, is 152 sq ft of flats — which at 10% waste is 17 boxes rather than 18. On a whole house with 40 linear ft of corner the deduction is 20 sq ft, or two full boxes.
The half-square-foot figure is a manufacturer convention, and it is not universal: Eldorado states about 0.5 sq ft per linear foot of corner, while Coronado's installation guide says a linear foot of corners consumes about 3/4 sq ft of wall. It is an input in the calculator above, so enter the figure from your own carton or installation guide.
Veneer for Common Walls
At 10% waste, 10 sq ft flat boxes and 6 linear ft corner boxes. Every figure is this calculator's own output:
| Wall | Gross Area | Corners | Flats to Order | Flat Boxes | Corner Boxes |
|---|---|---|---|---|---|
| 10 × 8 ft | 80 sq ft | 8 ft | 76 sq ft | 9 | 2 |
| 20 × 8 ft | 160 sq ft | 16 ft | 152 sq ft | 17 | 3 |
| 30 × 8 ft | 240 sq ft | 16 ft | 232 sq ft | 26 | 3 |
| 40 × 9 ft | 360 sq ft | 36 ft | 342 sq ft | 38 | 7 |
| 60 × 9 ft | 540 sq ft | 36 ft | 522 sq ft | 58 | 7 |
Notice the 30 ft and 40 ft rows. Corner linear feet do not scale with wall area — they scale with how many corners you have and how tall they are. A long unbroken wall needs almost no corners; a house with bump-outs needs a great many, and corners are where the cost is.
Ordering and Blending
Two pieces of advice that matter more for stone than for any other cladding, because both mistakes are permanent once the mortar sets.
Order the whole job at once. Manufactured stone is colored in batches, and boxes from different production runs can differ enough to read as a patch on a finished wall. There is no fixing it afterwards short of taking the stone off.
Blend as you work. Open several boxes and pull from all of them rather than emptying one before starting the next. Even inside a single run there is variation in color and in the mix of sizes, and working box by box lays that variation down in visible bands. Lay out a few square feet dry on the ground first and you will see how much the pieces differ.
The same goes for size and shape: pull the pieces you need to fit a spot from across the pile, rather than taking whatever is on top and cutting it.
What Goes Behind It
The stone is the last layer, and it is not the layer that keeps water out of the wall.
Over framing, manufactured stone goes on a water-resistive barrier, then lath, then a scratch coat — and it is the scratch coat the stone bonds to. Over clean, untreated masonry or concrete it can often be set directly. The wall assembly, the flashing at the base and the clearances above grade and above a roofline are what decide whether the wall dries out, and they are code matters that vary by jurisdiction: confirm them with your local code enforcement office before you start.
For the mortar itself, budget roughly one 80 lb bag per 15 sq ft across the setting bed and the joints — our mortar calculator covers it alongside brick and block. A dry-stacked look saves mortar in the joints but not in the setting bed, so do not halve the figure for it.
Frequently Asked Questions
How do I calculate stone veneer?
Work the flats and the corners separately, because they are sold in different units. Measure the wall area for the flats in square feet, and add up the height of every outside corner for the corners in linear feet. Then deduct about half a square foot of flats for every linear foot of corner, because the corner pieces already cover that area.
What is the difference between flats and corners?
Flats are the field stone that covers the face of a wall, sold by the square foot. Corners are L-shaped pieces with two finished faces that wrap an outside corner so you never see a cut edge, sold by the linear foot. Corners cost considerably more per piece, which is why the deduction is worth doing rather than ignoring.
Why do I deduct flats for corners?
Because a corner piece covers part of both walls it wraps. Every linear foot of corner takes up roughly half a square foot of the flat area you measured, so ordering the full wall area in flats and the corners separately double-counts that strip. On a house with 40 linear ft of corner that is 20 sq ft — two full boxes of flats you would never open.
How do I measure corners for stone veneer?
In linear feet of height, not in pieces. Measure how tall each outside corner is and add them up — two corners on an 8 ft wall is 16 linear ft. Inside corners do not need corner pieces at all: flats butt into an inside corner and the joint is mortared like any other.
How much stone veneer is in a box?
Flats commonly come 10 sq ft to a box and corners 6 to 8 linear ft, but this varies by manufacturer and by profile, and it is printed on the carton. Both are inputs here for that reason. Note that flat boxes are usually sold as a whole — you cannot buy 3 sq ft of the stuff.
How much waste should I allow for stone veneer?
10% on a plain wall, 15% where the elevation is broken up by windows, steps or changes of height. Veneer waste is different from tile waste: you are not cutting to a grid, you are fitting irregular pieces, so some of the allowance is stone you reject for shape rather than stone you cut.
How much mortar does stone veneer need?
Roughly one 80 lb bag per 15 square feet, covering both the setting bed and the joints — our mortar calculator works it out alongside brick and block. A dry-stacked look uses less in the joints but the same setting bed, so do not cut the figure in half for it.
Does stone veneer need a scratch coat?
Over most substrates, yes. Manufactured stone is installed over a water-resistive barrier and lath with a scratch coat, which is what the stone bonds to — the assembly matters more than the stone. Over a clean, untreated masonry or concrete wall the stone can often go straight on. Follow the manufacturer instructions, and confirm the wall assembly with your local code enforcement office.
Is manufactured stone the same as natural stone veneer?
No. Manufactured stone is cast concrete, colored through, light enough to hang on a framed wall, and sold in the flats-and-corners system this calculator uses. Natural thin veneer is real stone sawn thin; it is heavier, more variable, and often sold by the ton or by the pallet rather than by the box. If you are buying by weight, this page is the wrong tool.
Should I order all the stone at once?
Yes. Manufactured stone is colored in batches and boxes from different runs can differ noticeably, in a way that is obvious on a finished wall and impossible to fix afterwards. Order the whole job together, and blend from several boxes as you work rather than emptying one at a time — even within a single run there is variation, and working box by box lays it down in patches.
How many boxes of flats for a 160 square foot wall?
With 16 linear ft of outside corner, the corners cover 8 sq ft of that wall, leaving 152 sq ft of flats. At 10% waste and 10 sq ft to a box that is 17 boxes, plus 3 boxes of corners. Ordering the full 160 sq ft in flats without the deduction would have you buying an extra box for nothing.
Do inside corners need corner pieces?
No. Flats butt into an inside corner and the joint is mortared like any other — there is no exposed edge to hide. Corner pieces exist only for outside corners, where a cut flat would show its unfinished edge. Counting inside corners into your corner order is a common and expensive mistake.
Sources & Standards
- International Residential Code (ICC) — Residential construction requirements adopted by most US jurisdictions
Estimates for planning only. The figures here follow published model codes and industry standards, but those are adopted and amended locally, and older buildings are often legally exempt from the current edition. Check with your local code enforcement office or building department before you order or build — they are the authority that inspects the work, and what they require overrides anything on this page. See our full method and assumptions.