πŸ“ Area to Tile
ft
ft
πŸ”² Tile Size
in
in
βš™οΈ Options
The pattern decides how many tiles get cut, which is what the waste allowance is really for. Picking one sets the allowance below; you can still override it.
in
sq ft
Printed on the carton. Leave blank to skip the box count.
🧱 Setting Materials
Sorted by the tile’s longest side; the tile-size buttons pick one for you. Coverage per 50 lb bag is the same as on the mortar calculator.
in
For the grout: it fills the full joint depth.
βœ“ Results
Total Area 120.0 sq ft
Tile Coverage (each) 2.25 sq ft
Tiles Needed (exact) 53 tiles
+ Waste (10%) 6 tiles
59 tiles
Total Tiles to Purchase
Thin-set (50 lb bags) 3 bags
Grout 1 bag of 25 lb (7 lb sanded grout)
Backer board 9 sheets, about 486 screws, 72 ft of mesh tape

Need to know your room's square footage first?

Use our Square Footage Calculator β†’

How to Calculate Tiles Needed

Getting the right number of tiles prevents extra trips to the store and ensures you have matching tiles from the same dye lot.

The Basic Formula

Tiles = (Area Γ· Tile Size) Γ— (1 + Waste Factor)

Step by Step

Why Add Waste?

Tiles break, cuts don't always go right, and you'll want extras for future repairs. Standard practice is 10% for regular layouts, 15% for diagonal patterns.

On this page

  1. How to Calculate Tiles Needed
  2. Common Tile Sizes
  3. How Much Thinset, Grout, and Backer Board?
  4. Tile Layout Patterns and Waste
  5. Planning the Layout
  6. Frequently Asked Questions

Common Tile Sizes

Floor Tiles

Wall Tiles

Tiles per Square Foot

Useful for sanity-checking a box count before you leave the store:

Tile SizeArea per TileTiles per 100 Sq Ft+10% Waste
3 Γ— 6 in (subway)0.125 sq ft800880
4 Γ— 4 in0.111 sq ft900990
6 Γ— 6 in0.25 sq ft400440
12 Γ— 12 in1.0 sq ft100110
12 Γ— 24 in2.0 sq ft5055
18 Γ— 18 in2.25 sq ft4550
24 Γ— 24 in4.0 sq ft2528
6 Γ— 24 in (plank)1.0 sq ft100110

How Much Thinset, Grout, and Backer Board?

Tile is only part of the order. These are the materials people forget until they're already at the store:

MaterialCoverageNotes
Thinset (50 lb bag)20–95 sq ftDepends heavily on trowel size
Grout (25 lb bag)About 25–700 sq ftSet by tile size, thickness and joint: Custom’s Polyblend chart gives 348 sq ft for 12Γ—12Γ—3/8 in tile at 1/8 in, 121 at 3/8 in, and 54 for 1Γ—1 mosaic at 1/8 in
Cement backer board15 sq ft per 3Γ—5 sheetWet areas and most floors
Backer board screws~54 per sheet on a floor, ~27 on a wallOne every 8 in (James Hardie); use screws rated for backer board
Alkali-resistant mesh tapeAbout 8 ft per sheet2 in wide, on every seam

Trowel size drives thinset consumption more than anything else. Custom Building Products’ VersaBond sheet gives 85–95 sq ft per 50 lb bag with a 1/4 Γ— 1/4 in square notch and 60–67 with a 1/4 Γ— 3/8 in notch; its large-format FlexBond sheet gives 45–50 with a 1/2 Γ— 1/2 in notch and 36–40 with a 3/4 Γ— 9/16 in U-notch. The calculator uses the low end of each (85, 60 and 45). For a deep 3/4 Γ— 3/4 in U-notch it plans 30, and 22 when you also back-butter every tile for 95% contact in a shower; those two are our own allowances, not manufacturer figures. Match the notch to the tile: bigger tile needs a bigger notch to get full coverage underneath.

The calculator adds these to the tile count. Thin-set is the area plus 10%, divided by the trowel’s coverage: 120 sq ft of 18 × 18 in tile with a 1/2 × 1/2 in notch is 132 ÷ 45 = 2.9, or 3 bags. Grout comes from the joint volume: tile length plus width, times the joint width and the tile thickness, over the tile’s face area, at about 0.064 lb of dry grout per cubic inch, the rate behind Custom’s Polyblend coverage chart. For 18 × 18 in tile 3/8 in thick with 1/8 in joints that is 0.75 cubic inches, or 0.048 lb, per sq ft: 6.3 lb with the allowance for 120 sq ft, so 7 lb, and the chart gives 518 sq ft per 25 lb bag for the same tile. Backer board is the area plus 10% in 3 × 5 ft (15 sq ft) sheets. James Hardie’s instructions call for a fastener at most every 8 in over the whole sheet on a floor, about 54 screws per sheet, and every 8 in along each stud on a wall, about 27 per sheet on studs 16 in apart. Every seam gets 2 in alkali-resistant mesh tape; a sheet has 16 ft of edge, shared with its neighbors, so allow about 8 ft per sheet. The mortar calculator works the same numbers in more detail.

For large-format tile β€” anything with a side over 15 inches β€” use a medium-bed or large-format mortar rather than standard thinset. Regular thinset shrinks as it cures, which leaves hollow spots under a big tile.

Sanded or Unsanded Grout?

Tile Layout Patterns and Waste

Where the cuts fall: straight grid versus diagonal Two plan views of the same rectangular room tiled with the same square tile. On the left the tiles run square to the walls: full tiles fill the field and only the tiles along two walls are cut, each into a rectangle. On the right the same grid is turned 45 degrees: every tile touching any wall is cut, and each offcut is a triangle rather than a rectangle, so far more tiles are cut for the same floor area. Square to the wallsWaste allowance 10%Turned 45°Waste allowance 15%14 tiles cut, all rectanglesThe offcuts are the same size as each other, so they pair up.36 tiles cut, all trianglesA triangle only suits the opposite corner, so most are scrap.full tilecut tile
Fig. 1 — The same room and the same tile, laid square to the walls and turned 45°. Shaded tiles are cut. Square to the walls the cuts sit only where the field meets a wall and every offcut is a rectangle; on the diagonal every perimeter tile is cut and the offcut is a triangle, which is why the allowance goes from 10% to 15%. Herringbone cuts more again — see the table above.

The pattern you lay changes how much tile you have to buy, and it is the part most estimates skip. Waste is not breakage — it is offcuts you cannot use anywhere else. The more tiles that get cut, and the more awkward the shape of what is left over, the more you need.

PatternHow the Tiles SitWhere the Cuts FallWaste Allowance
Straight grid (stacked)Joints line up in both directionsPerimeter only10%
Running bond / offsetEach row shifts a half or a third of a tilePerimeter, plus the part tile that starts alternate rows10%
BasketweavePairs of rectangles alternating directionPerimeter, and the pattern has to finish on a whole block15%
Diagonal (45Β°)The whole grid turned 45Β° to the wallsEvery perimeter tile cut on an angle15%
HerringboneRectangles at right angles to each other, run at 45Β°Every perimeter tile cut at 45Β°, often at both ends20%

In a straight grid the offcut from the end of one row is often the right size to start the next, so very little is truly wasted. Turn the same grid 45° and every perimeter tile becomes a triangle whose remainder is a triangle too — and a triangle only fits the opposite corner, not the next cut along. That is the whole reason an angled layout costs more tile, not the pattern being "harder".

The difference is easy to underestimate. A 10 × 12 ft floor in 12 × 12 in tile with a 1/8 in joint needs 118 tiles of actual coverage. Buy for it as a straight grid and you order 130; diagonally, 136; in herringbone, 142. Same floor, same tile, 12 extra tiles between the easiest and the hardest layout.

Picking a tile that herringbones cleanly

Herringbone wants a rectangle whose length is a clean multiple of its width — a true 2:1 tile such as 6 × 12 or 4 × 8 interlocks with the short edge landing exactly halfway along the long edge. Off-ratio planks such as 6 × 24 or 8 × 36 still work, but the join no longer lands on a tile edge, so the pattern reads as a zigzag rather than a weave and the perimeter cuts stop repeating. If you want the cuts to repeat, choose the ratio before you choose the color.

Note that chevron is not herringbone: chevron tiles meet point to point in a continuous V, which needs tiles pre-cut as parallelograms or every single tile mitred. Budget the same 20% and expect more cutting time.

Whichever pattern you pick, where you start it still decides how the cuts look — see the layout steps below.

Planning the Layout

Where you start the first tile determines how the whole floor looks. A few minutes of dry layout prevents the classic mistake of a sliver of tile along the most visible wall.

  1. Find the center of the room by snapping chalk lines between the midpoints of opposing walls. Check they're square with each other.
  2. Dry-lay a row in each direction from center to wall, including grout gaps, and see what the cut at the end looks like.
  3. Shift the layout by half a tile if you end up with a cut narrower than about a third of a tile. Moving the start point turns two ugly slivers into two decent cuts.
  4. Prioritize the sight line. Full tiles should land where you look first β€” the doorway, the front of a vanity β€” and cuts should go under cabinets and along the least visible wall.
  5. Check the floor is flat. Large-format tile needs flatness within 1/8 inch over 10 feet. Fix low spots with a self-leveling underlayment before tiling, not with extra thinset.
  6. Stagger plank tile by a third, not a half. Half-offsets on long planks can produce a visible lippage ridge, because most planks have slight crown along their length.

Need to work out the area first? Start with the square footage calculator, or head to the backsplash and shower tile calculators for those specific jobs.

Frequently Asked Questions

How many tiles in a box?

It varies by manufacturer, so check the carton for the square feet it covers. Enter that in Sq Ft per Box and the calculator works out how many tiles each box holds from the tile size, then rounds up to whole boxes.

Do I count the grout lines?

The calculator counts the joint as part of each tile’s footprint, which trims a few tiles: 100 sq ft of 12 × 12 in tile with 1/8 in joints is 98 tiles rather than 100. Set the gap to 0 to leave it out.

What if my room isn't a rectangle?

Split it into rectangles at the inside corner and enter each one in the L-Shape or Several Areas tab; the calculator adds them and applies the waste once. For curves or angles, total the area on the square footage calculator and use Total Square Feet.

Should I buy extra tiles?

Always. Keep 2-3 extra tiles stored away for future repairs. Tile colors can vary between production runs.

How many 12x12 tiles do I need for 100 square feet?

A 12 Γ— 12 in tile is exactly 1 square foot, so 100 tiles covers 100 sq ft of face β€” 110 with the standard 10% waste. With a 1/8 in grout joint each tile covers a little more, so the calculator gives 98 tiles, or 108 with waste. For 12 Γ— 24 in tile it's 50 tiles (55 with waste) either way, and for 18 Γ— 18 in it's 45 (50 with waste) by face area, or 44 (49) with the joint.

How much thinset do I need?

It depends on the trowel. By Custom Building Products’ published charts, a 50 lb bag covers about 85–95 sq ft with a 1/4 Γ— 1/4 in notch, 60–67 with 1/4 Γ— 3/8, 45–50 with 1/2 Γ— 1/2, and 36–40 with a 3/4 in U-notch; back-buttering large tile cuts it further. Pick your notch in the calculator and it counts the bags from the low end of each range.

How much grout do I need?

It depends almost entirely on tile size and joint width. Custom Building Products' Polyblend sanded chart puts a 25 lb bag at about 348 square feet for 12 Γ— 12 Γ— 3/8 in tile with a 1/8 in joint, 121 square feet for the same tile at 3/8 in, and only 54 square feet for 1 Γ— 1 in mosaic at 1/8 in. Small tiles and wide joints use far more than large tiles with tight joints: at 1/8 in, the chart gives 688 sq ft per bag for 24 Γ— 24 in floor tile, so 1 in mosaic uses over twelve times as much per square foot.

What size trowel should I use?

Match the notch to the tile’s longest side: 1/4 Γ— 1/4 in for mosaic and tile up to about 8 inches, 1/4 Γ— 3/8 in for 8 to 15 inches, and 1/2 Γ— 1/2 in or a 3/4 in U-notch for anything longer, which is how Custom’s large-format mortar sheet sorts it. Too small a notch leaves voids under the tile, which is what causes cracking and hollow spots later.

Sanded or unsanded grout?

Sanded for joints 1/8 inch and wider β€” the sand prevents shrinkage cracking. Unsanded for narrower joints and for polished stone or glass tile, where sand would scratch the surface.

Do I need backer board under tile?

In wet areas, yes β€” cement backer board or an equivalent waterproof substrate. On dry floors over plywood, backer board or an uncoupling membrane is strongly recommended: tile set straight onto plywood cracks as the wood moves with humidity.

Where should I start laying tile?

From the center of the room, not a wall. Snap chalk lines between the midpoints of opposite walls, dry-lay a row each way, and shift the layout half a tile if you'd otherwise end with a sliver at the edge. Full tiles belong where the eye lands first.

How flat does the floor need to be for large tile?

Within about 1/8 inch over 10 feet for tile 15 inches or larger. Large-format tile can't flex to follow a dip, so a low spot becomes lippage or a cracked tile. Fix it with self-leveling underlayment before you tile β€” not with extra mortar.

How much extra tile do I need for a herringbone pattern?

Allow 20%, against 10% for a straight grid. Every tile around the perimeter is cut at 45°, often at both ends, and the triangular offcuts rarely fit anywhere else. On a 10 × 12 ft floor in 12 × 12 in tile that is 142 tiles instead of 130 — pick Herringbone in the calculator above and it sets the allowance for you.

Does diagonal tile use more tile?

It covers exactly the same area, but you buy more: allow 15% instead of 10%. Turning the grid 45° means every tile meeting a wall is cut on an angle, and the leftover triangles only suit the opposite corner. The tile itself is no bigger; the offcuts are just less reusable.

What is running bond tile?

Running bond is the brick-style offset where each row shifts sideways relative to the one below, instead of lining up in a grid. Waste stays at about 10%, because the part tile that starts every second row is usually the offcut from the end of the previous one. On long plank tile, stagger by a third rather than a half — a half-offset can show a lippage ridge, since most planks crown slightly along their length.

Sources & Standards

Estimates for planning only. Quantities are calculated from standard coverage and yield figures, with a waste allowance where the page states one. Always confirm against the manufacturer figures on the product you buy, and check local requirements before ordering. See our full method and assumptions.

Last updated Β· How we calculate